Bedienungsanleitung Pioneer VSX-1019AH-K (Seite 57 von 128) (Englisch)

455217

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

Listening to your system 06

Using the Virtual Surround Back

mode

•Default setting: ON

When you’re not using surround back

speakers, selecting this mode allows you to

hear a virtual surround back channel through

your surround speakers. You can choose to

listen to sources with no surround back

channel information, or if the material sounds

better in the format (for example, 5.1) for which

it was originally encoded, you can have the

receiver only apply this effect to 6.1 encoded

sources like Dolby Digital EX or DTS-ES.

• Press

SBch

repeatedly to cycle the virtual

surround back channel options.

Each press cycles through the options as

follows:

• VirtualSB ON – Virtual Surround Back is

always used (for example, on 5.1 encoded

material)

• VirtualSB AUTO – Virtual Surround Back

is automatically applied to 6.1 encoded

sources (for example, Dolby Digital EX or

DTS-ES)

• VirtualSB OFF – Virtual Surround Back

mode is switched off

Setting the Up Mix function

In a 7.1-channel surround system with

surround speakers placed directly at the sides

of the listening position, the surround sound of

5.1-channel sources is heard from the side. The

Up Mix function mixes the sound of the

surround speakers with the surround back

speakers so that the surround sound is heard

from diagonally to the rear as it should be.

•Using the Up Mix function is effective when

the speakers in the 7.1-channel surround

system are set up as recommended in the

example on page 17.

•Depending on the positions of the speakers

and the sound source, in some cases it

may not be possible to achieve good

results. In this case, set the setting to OFF.

1 Switch the receiver into standby.

2 While holding down

ENTER

on the front

panel, press

 STANDBY/ON

The display shows RESET  NO .

Use TUNE +/– (or / on the remote control)

to select UP MIX ON , and then use

PRESET +/– (or / on the remote control) to

select ON or OFF.

3Press

ENTER

to confirm.

• When set to ON, the UP MIX indicator on

the front panel lights.

Note

1 • You can’t use the Virtual Surround Back mode when the headphones are connected to this receiver or when any of

the stereo, Front Stage Surround Advance or Stream Direct mode is selected.

• You can only use the Virtual Surround Back mode if the surround speakers are on and the SB setting is set to NO

or if Front Bi-Amp, Speaker B or Zone 2 is selected at Surr Back System.

• The Virtual Surround Back mode cannot be applied to sources that do not have surround channel information.

2 • Set to ON regardless of this setting when playing DTS-HD signals.

• May automatically be set to OFF even when set to ON, depending on the input signal and listening mode.

FL FR

SL SR

SBL SBR SBL SBR

FL FR

SL SR

Up Mix OFF Up Mix ON

VSX-1019_KU.book 57 ページ２００９年２月１７日　火曜日　午前１１時５６分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-1019AH-K Seite 57

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-1019AH-K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info