Bedienungsanleitung Pioneer VSX-1020-K (Seite 23 von 35) (Englisch)

574080

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

How to Interpret the Graphs (Continued)

About the types of displays of the graph for the reverb

characteristics after EQ calibration

For “SYMMETRY” or “FRONT ALIGN”

• The display type is set to “Pair Ch” (page 12). For reasons of the properties of the different EQ curves,

when the “Each Ch” display type is set, the reverb characteristics for the different channels do not line up

properly.

• The reverb characteristics prior to calibration are displayed in the “Each Ch” mode, so if you want to

compare the characteristics before and after calibration, set the display type prior to calibration to “Pair

Ch”. This way the number of channels before and after calibration are the same, allowing you to compare.

For “ALL CH ADJ”

• The display type is set to “Each Ch” (page 12). For reasons of the properties of the EQ curves, when the

“Pair Ch” display type is set, the reverb characteristics for the different pairs of channels do not line up

properly.

• Since the “Each Ch” display type is set both before and after calibration, the graphs can be compared as

such.

Displaying the reverb characteristics after EQ calibration (actually

measured values)

The graphs for before and after calibration can be displayed at the screen displaying the graphs of the

reverberation characteristics after Full Auto MCACC (EQ Type:SYMMETRY) measurements, but note that the

graph displayed here for the characteristics after calibration is a prediction of the reverb characteristics

after MCACC calibration. If you want to check the graph of the actually measured reverberation

characteristics after MCACC calibration (not the prediction), you must re-measure the reverb characteristics

after calibration. To do so, follow the procedure described below. If the “Full Auto MCACC” operation has

never been performed, conduct the “Full Auto MCACC” operation here. (See the receiver’s Operating

Instructions.)

1 Select the “EQ Professional” option for “Manual MCACC”, and perform with

“Reverb Measurement” set to “EQ ON”. (See the receiver’s Operating Instruc-

tions.)

Measure the room’s reverb characteristics after equalization with the microphone at the same position as

when the “Full Auto MCACC” operation was performed. The measurements are performed with the EQ

values stored in the MCACC memory selected on the receiver, so before measuring the reverb

characteristics, select the MCACC memory to be measured after equalization.

2 Select “Output MCACC data” from “MCACC Data Check”.

3 Connect your USB device to the USB terminal on the front panel, then select

“OK”.

4 Connect the USB device onto which the measurement data was transferred to

the computer’s USB port, then open the measurement data.

You can display the graph of the reverberation characteristics actually measured after EQ calibration by

displaying the Reverb graph and selecting “After”.

Continue

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-1020-K Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-1020-K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info