Bedienungsanleitung Pioneer VSX-1021K (Seite 25 von 184) (Englisch, Spanisch)

455184

Zoom out

Zoom in

Vorherige Seite

1/184

Nächste Seite

Basic Setup

5 Follow the instructions on-screen.

Make sure the microphone is connected, and

if you’re using a subwoofer, make sure it is

switched on and set to a comfortable volume

level.

6 Wait for the test tones to finish, then

confirm the speaker configuration in the

GUI screen.

A progress report is displayed on-screen while

the receiver outputs test tones to determine

the speakers present in your setup. Try to be as

quiet as possible while it’s doing this.

If no operations are performed for 10 seconds

while the speaker configuration check screen

is being displayed, the Full Auto MCACC Setup

will resume automatically. In this case, you

don’t need to select ‘OK’ and press ENTER in

step 7.

! With error messages (such as Too much

ambient noise! or Check microphone.),

select RETRY after checking for ambient

noise (see Problems when using the Auto

MCACC Setup on page 25 ) and verifying the

mic connection. If there doesn’t seem to be

a problem, you can simply select GO NEXT

and continue.

Now Analyzing... 2/9

Environment Check

1a.Full Auto MCACC

A/V RECEIVER

Ex it Ca nc el

Ambient Noise : OK

Microphone :

Speaker YES/NO :

L : YES

FHL : YES

C : YES

FHR : YES

R : YES

SR : YES

SBR : YES

SBL : YES

SL : YES

SW : YES

1a.Full Auto MCACC

OK RETRY

A/V RECEIVER

Ex it Ca nc el

The configuration shown on-screen should

reflect the actual speakers you have.

! If you see an ERR message (or the speaker

configuration displayed isn’t correct),

there may be a problem with the speaker

connection. If selecting RETRY doesn’t work,

turn off the power and check the speaker

connections. If there doesn’t seem to be a

problem, you can simply use i/j to select

the speaker and k/l to change the setting

and continue.

! If the speaker is not pointed to the

microphone (listening position) or when

using speakers that affect the phase

(dipole speakers, reflective speakers, etc.),

Reverse Phase may be displayed even if the

speakers are properly connected.

If Reverse Phase is displayed, the speaker’s

wiring (+ and –) may be inverted. Check the

speaker connections.

— If the connections were wrong, turn off

the power, disconnect the power cord,

then reconnect properly. After this,

perform the Full Auto MCACC procedure

again.

— If the connections were right, select

GO NEXT and continue.

7 Make sure ‘OK’ is selected, then press

ENTER.

A progress report is displayed on-screen while

the receiver outputs more test tones to deter-

mine the optimum receiver settings.

Again, try to be as quiet as possible while this is

happening. It may take 3 to 10 minutes.

8 The Full Auto MCACC Setup procedure

is completed and the Home Menu menu

reappears automatically.

Be sure to disconnect the microphone from

this receiver upon completion of the Full Auto

MCACC Setup.

The settings made in the Full Auto MCACC

Setup should give you excellent surround

sound from your system, but it is also possible

to adjust these settings manually using The

Advanced MCACC menu on page 58 or The

System Setup and Other Setup menus on page

64 .

! Depending on the characteristics of your

room, sometimes identical speakers with

cone sizes of around 12 cm (5 inches) will

end up with different size settings. You

can correct the setting manually using the

Manual speaker setup on page 64 .

! The subwoofer distance setting may be

farther than the actual distance from the

listening position. This setting should

be accurate (taking delay and room

characteristics into account) and generally

does not need to be changed.

! If Full Auto MCACC Setup measurement

results are incorrect due to the interaction of

the speakers and viewing environment, we

recommend adjusting the settings manually.

Problems when using the Auto

MCACC Setup

If the room environment is not optimal for the

Auto MCACC Setup (too much background

noise, echo off the walls, obstacles blocking

the speakers from the microphone) the final

settings may be incorrect. Check for household

appliances (air conditioner, fridge, fan, etc.),

that may be affecting the environment and

switch them off if necessary. If there are any

instructions showing in the front panel display,

please follow them.

! Some older TVs may interfere with the

operation of the microphone. If this seems to

be happening, switch off the TV when doing

the Auto MCACC Setup.

The Input Setup menu

You only need to make settings in the

Input Setup menu if you didn’t hook up your

digital equipment according to the default

settings (see Input function default and possible

settings on page 26 ). In this case, you need to

tell the receiver what equipment is hooked up

to which terminal so the buttons on the remote

control correspond to the components you’ve

connected.

1 Press on the remote control,

then press HOME MENU.

A Graphical User Interface (GUI) screen

appears on your TV. Use i/j/k/l and

ENTER to navigate through the screens and

select menu items. Press RETURN to exit the

current menu.

2 Select ‘System Setup’ from the

Home Menu.

3 Select ‘Input Setup’ from the

System Setup menu.

A/V RECEIVER

Ex it Return

a. Ma nu al S P Setup

b. Input Set up

c. OSD Language

d. Network S et up

e. HDMI Setup

f. Other Setup

4.System Setup

4b.Input Setup

A/V RECEIVER

Ex it F in is h

Input : DVD

Input Name : Rename

Digital In : COAX-1

HDMI Input : DVD

Input Skip : OFF

Component In : In-1

4 Select the input function that you

want to set up.

The default names correspond with the names

next to the terminals on the rear panel (such as

DVD or VIDEO 1) which, in turn, correspond

with the names on the remote control.

Pioneer VSX-1021K Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-1021K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info