Bedienungsanleitung Pioneer VSX-1122K (Seite 89 von 107) (Englisch)

491802

Zoom out

Zoom in

Vorherige Seite

1/107

Nächste Seite

FAQ

Professional Calibration EQ graphical output

Symptom Remedy

The reverb characteristics graph

after EQ calibration does not appear

entirely flat.

There are cases where the graph does not appear flat (even when selecting ALL CH ADJ

in the Auto MCACC Setup) due to adjustments made to compensate for room character-

istics to achieve optimal sound.

Areas of the graph may appear identical (before and after) when there is little or no

adjustment needed.

The graph may appear to have shifted vertically when comparing before and after mea-

surements.

EQ adjustments made using the

Manual MCACC setup do not appear

to change the reverb characteristics

graph after EQ calibration.

Despite level adjustments being made, the filters used for analysis may not display these

adjustments in the reverb characteristics graph after EQ calibration. However, these

adjustments are taken into account by the filters dedicated to overall system calibration.

Lower frequency response curves do

not seem to have been calibrated for

SMALL speakers.

Low frequencies used in bass management (the subwoofer channel) will not change for

speakers that have been specified as SMALL in the configuration, or do not output these

frequencies.

Calibration is performed, but due to your speakers’ low frequency limitations, no measur-

able sound is output for display.

Display

Symptom Remedy

The display is dark or off. Press DIMMER repeatedly to select a different brightness.

The OSD screen is not displayed. The OSD screen is not displayed unless the receiver and TV are connected using an

HDMI cable. If the TV does not support HDMI, perform the various operations and make

the settings while watching the display on the receiver’s front panel.

You can’t get DIGITAL to display

when using SIGNAL SEL.

Check the digital connections and make sure that the digital inputs are assigned cor-

rectly (see The Input Setup menu on page 35).

2 DIGITAL or DTS does not light

when playing Dolby/DTS software.

These indicators do not light if playback is paused.

Check the playback (especially the digital output) settings of the source component.

When playing Dolby Digital or DTS

sources, the receiver’s format indica-

tors do not light.

Check that the player is connected using a digital connection.

Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on

page 46).

Check that the player isn’t set up so that Dolby Digital and DTS sources are converted to

PCM.

Ensure that if there are several audio tracks on the disc, the Dolby Digital or DTS is

selected.

When playing certain discs, none of

the receiver’s format indicators light.

The disc may not contain 5.1/6.1 channel material. Check the disc packaging for more on

what audio tracks are recorded on the disc.

When playing a disc with the listen-

ing mode set to Auto Surround or

ALC, 2 Pro Logic II or DTS Neo:6

appear on the receiver.

Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on

page 46).

If a two channel soundtrack is currently playing (including Dolby Surround encoded),

then this is not a malfunction. Check the disc packaging for details about the audio

tracks available.

During playback of DVD-Audio, the

display shows PCM.

This will occur when playing DVD-Audio material over the HDMI connection. This is not a

malfunction.

Symptom Remedy

The power turns off automatically

and some indicator flashes, or some

indicator flashes and the power does

not turn on.

See the Power section (page 86).

Remote control

Symptom Remedy

Cannot be remote controlled. Set the remote control unit’s remote control mode so that it matches the setting on the

main unit (see Operating multiple receivers on page 66).

Check whether the receiver’s remote control mode is properly set (see Remote Control

Mode Setup on page 84).

Try replacing the batteries in the remote control (see Loading the batteries on page 8).

Be sure to operate within 7 m (23 ft.) and a 30º angle of the remote sensor on the front

panel (see Operating range of remote control unit on page 8).

Check that there are no obstacles between the receiver and the remote control.

Make sure that there is no fluorescent or other strong light shining on to the remote

sensor.

Other components can’t be operated

with the system remote.

If the battery ran down, the preset codes may have been cleared. Re-enter the preset

codes.

The preset code may be incorrect. Redo the procedure for entering preset codes.

When commands from the remote control units of other devices are registered using the

learning function, in some cases they may not be learned properly. In this case, register

the commands again using the learning function (see page 67). If they still do not work,

they may be in a special format that cannot be registered on this receiver’s remote con-

trol. Operate the device using another remote control.

HDMI

Symptom Remedy

The HDMI indicator blinks continu-

ously.

Check all the points below.

No picture or sound. This receiver is HDCP-compatible. Check that the components you are connecting are

also HDCP-compatible. If they are not, please connect them using the component or

composite video jacks.

Depending on the connected source component, it’s possible that it will not work with

this receiver (even if it is HDCP-compatible). In this case, connect using the component

or composite video jacks between source and receiver.

If the problem still persists when connecting your HDMI component directly to your

monitor, please consult the component or monitor manual or contact the manufacturer

for support.

If video images do not appear on your TV, try adjusting the resolution, Deep Color or other

setting for your component.

While analog video signals are being output over HDMI, use a separate connection for

audio output.

To output signals in Deep Color, use an HDMI cable (High Speed HDMI

Cable) to

connect this receiver to a component or TV with the Deep Color feature.

Pioneer VSX-1122K Seite 89

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-1122K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info