Bedienungsanleitung Pioneer VSX-1123-K (Seite 88 von 113) (Englisch)

574087

Zoom out

Zoom in

Vorherige Seite

1/113

Nächste Seite

The System Setup and Other Setup menus

! LAST (default) – When the power is turned on, the volume is set to the same level as when the power was last

turned off.

! “---” – When the power is turned on, the volume is set to minimum level.

! –80.0dB to +12.0dB – Specify the volume to be set when the power is turned on, in steps of 0.5 dB.

It is not possible to set a volume level greater than the value specified at Volume Limit setup (see below).

3 Select the Volume Limit setting you want.

Use this function to limit the maximum volume. The volume cannot be increased above the level set here, even by

operating VOLUME button (or the dial on the front panel).

! OFF (default) – The maximum volume is not limited.

! –20.0dB/–10.0dB/0.0dB – The maximum volume is limited to the value set here.

4 Select the Mute Level setting you want.

This sets how much the volume is to be turned down when MUTE is pressed.

! FULL (default) – No sound.

! –40.0dB/–20.0dB – The volume will be turned down to the level specified here.

5 When you’re finished, press RETURN.

You will return to the Other Setup menu.

Remote Control Mode Setup

! Default setting: 1

This sets this receiver’s remote control mode to prevent erroneous operation when multiple units of the receiver

are being used.

1 Select ‘Remote Control Mode Setup’ from the Other Setup menu.

2 Select the Remote Control Mode setting you want.

3 Select ‘OK’ to change the remote control mode.

4 Follow the instructions on the screen to change the remote control’s setting.

See Operating multiple receivers on page 71.

5 When you’re finished, press RETURN.

You will return to the Other Setup menu.

Software Update

Use this procedure to update the receiver’s software and check the version. There are two ways to update: via the

Internet and via a USB memory device.

Updating via the Internet is performed by accessing the file server from the receiver and downloading the file.

This procedure is only possible if the receiver is connected to the Internet.

Updating via a USB memory device is performed by downloading the update file from a computer, reading this

file onto a USB memory device then inserting this USB memory device into the USB port on the receiver’s front

panel. With this procedure, the USB memory device containing the update file must first be inserted into the USB

port on the receiver’s front panel.

! If an update file is provided on the Pioneer website, download it onto your computer. When downloading an

update file from the Pioneer website onto your computer, the file will be in ZIP format. Unzip the ZIP file before

saving it on the USB memory device. If there are any old downloaded files or downloaded files for other models

on the USB memory device, delete them.

Important

! DO NOT unplug the power cord during updating.

! When updating via the Internet, do not disconnect the LAN cable. When updating via a USB memory device,

do not disconnect the USB memory device.

! If updating is interrupted before it is completed, start updating over from the beginning.

! The receiver’s settings may be reset when the software is updated. Information on the models for which the

settings are reset is provided on the Pioneer website. Check the website before updating.

1 Select ‘Software Update’ from the Other Setup menu.

2 Select the update procedure.

! Update via Internet – The receiver checks whether updatable software is available via the Internet.

! Update via USB Memory – The receiver checks whether the USB memory device inserted into the USB port

on the receiver’s front panel contains updatable software.

“Accessing” is displayed and the update file is checked. Wait a while.

3 Check on the screen whether or not an update file was found.

If “New version found.” is displayed, the update file has been found. The version number and updating time are

displayed.

If “This is the latest version. There is no need to update.” is displayed, no update file has been found.

4 To update, select OK.

The updating screen appears and updating is performed.

! The power turns off automatically once updating is completed.

Software Update messages

Status messages Descriptions

FILE ERROR

Try disconnecting then reconnecting the USB device or storing the update file again. If the error still

occurs, try using a different USB memory device.

No update file was found on the USB memory device. Store the file in the USB memory device’s root

directory.

UPDATE ERROR 1 to

UPDATE ERROR 7

Turn the receiver’s power off, then turn it back on and try updating the software again.

Update via USB

If this message flashes, updating has failed. Update via a USB memory device. Put the update file on a

USB memory device and connect the device to the USB port. When the file is found, software updating

starts automatically.

UE11

Updating has failed. Use the same procedure to update the software again.

UE22

UE33

ZONE Setup

The volume setting for the sub zones that can be used with this receiver can be changed here.

CAUTION

! Note that when Volume Level is set to 0 dB Fixed, the audio output from the AUDIO ZONE 2 OUT terminals

is set to the maximum. Also, depending on the volume setting on the connected amplifier, large volumes may

be produced even when Volume Level is set to –40 dB Fixed.

1 Select ‘ZONE Setup’ from the Other Setup menu.

2 Select ‘ZONE 2’, then press ENTER.

Pioneer VSX-1123-K Seite 88

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-1123-K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info