Bedienungsanleitung Pioneer VSX-1123 (Seite 33 von 115) (Englisch)

536829

Zoom out

Zoom in

Vorherige Seite

1/115

Nächste Seite

Connecting your equipment

Connecting an IR receiver

If you keep your stereo components in a closed cabinet or shelving unit, or you wish to use the sub zone remote

control in another zone, you can use an optional IR receiver (such as a Niles or Xantech unit) to control your

system instead of the remote sensor on the front panel of this receiver.

! Remote operation may not be possible if direct light from a strong fluorescent lamp is shining on the IR

receiver remote sensor window.

! Note that other manufacturers may not use the IR terminology. Refer to the manual that came with your com-

ponent to check for IR compatibility.

! If using two remote controls (at the same time), the IR receiver’s remote sensor takes priority over the remote

sensor on the front panel.

1 Connect the IR receiver sensor to the IR IN jack on the rear of this receiver.

OUT

Closet or shelving unit

Non-Pioneer

component

IR receiver

2 Connect the IR IN jack of another component to the IR OUT jack on the rear of this receiver

to link it to the IR receiver.

Please see the manual supplied with your IR receiver for the type of cable necessary for the connection.

Plugging in the receiver

Only plug in after you have connected all your components to this receiver, including the speakers.

CAUTION

! Handle the power cord by the plug part. Do not pull out the plug by tugging the cord, and never touch the

power cord when your hands are wet, as this could cause a short circuit or electric shock. Do not place the

unit, a piece of furniture, or other object on the power cord or pinch the cord in any other way. Never make a

knot in the cord or tie it with other cables. The power cords should be routed so that they are not likely to be

stepped on. A damaged power cord can cause a fire or give you an electric shock. Check the power cord once

in a while. If you find it damaged, ask your nearest Pioneer authorized independent service company for a

replacement.

! Do not use any power cord other than the one supplied with this unit.

! Do not use the supplied power cord for any purpose other than that described below.

! The receiver should be disconnected by removing the mains plug from the wall socket when not in regular use,

e.g., when on vacation.

1 Plug the supplied power cord into the AC IN socket on the back of the receiver.

2 Plug the other end into a power outlet.

! After this receiver is connected to an AC outlet, a 2 second to 10 second HDMI initialization process begins.

You cannot carry out any operations during this process. The HDMI indicator in the front panel display blinks

during this process, and you can turn on this receiver once it has stopped blinking. When you set the Control

with HDMI to OFF, you can skip this process. For details about the Control with HDMI feature, see Control

with HDMI function on page 58.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-1123 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-1123

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info