Bedienungsanleitung Pioneer VSX-1123 (Seite 92 von 115) (Englisch)

536829

Zoom out

Zoom in

Vorherige Seite

1/115

Nächste Seite

FAQ

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong

with this component, check the points below. Sometimes the trouble may lie in another component. Investigate

the other components and electrical appliances being used. If the trouble cannot be rectified even after exercis-

ing the checks listed below, ask your nearest Pioneer authorized independent service company to carry out repair

work.

! If the unit does not operate normally due to external effects such as static electricity disconnect the power plug

from the outlet and insert again to return to normal operating conditions.

If the problem is not solved after the troubleshooting below, if the screen freezes unexpectedly or if the buttons on

the remote control or front panel stop working completely, do the following:

! Press u STANDBY/ON on the front panel to turn off the power, then turn the power back on.

If this does not solve the problem, turn off the power again, then press and hold the u STANDBY/ON button

on the front panel for at least 10 seconds. (The power turns on, then turns off after 10 seconds.)

! If the power cannot be turned off, press and hold u STANDBY/ON on the front panel for over 10 seconds. The

power will turn off. In this case, the various settings made on the receiver may be cleared. (However, settings

made when the power was turned off normally are not cleared.)

Power

Symptom Remedy

The power does not turn on. Make sure that the power cord is plugged in to an active power outlet.

Try disconnecting from the power outlet, then plugging back in.

Power cannot be turned off.

(ZONE 2 ON is displayed.)

Press the ZONE 2 button on the remote control, then press u STANDBY/ON to turn the

power off. Next, press RECEIVER to set the remote control back to the AV amplifier control

mode.

Power cannot be turned off.

(HDZONE ON is displayed.)

Press the HDZONE button on the remote control, then press u STANDBY/ON to turn

the power off. Next, press RECEIVER to set the remote control back to the AV amplifier

control mode.

The receiver suddenly switches off

or the iPod iPhone iPad indicator

blinks.

Check that there are no loose strands of speaker wire touching the rear panel or another

set of wires. If so, re-attach the speaker wires, making sure there are no stray strands.

The receiver may have a serious problem. Disconnect from the power and call a Pioneer

authorized independent service company.

During loud playback the power sud-

denly switches off.

Turn down the volume.

Lower the 63 Hz and 125 Hz equalizer levels in the Manual MCACC setup on page 78.

Switch on the digital safety feature. While holding down ENTER on the front panel,

press u STANDBY/ON to set this receiver to the standby mode. Use TUNE i/j to

select D.SAFETY cOFFd, and then use PRESET k/l to select 1 or 2 (select D.SAFETY

cOFFd to deactivate this feature). If the power switches off even with 2 switched on, turn

down the volume. With 1 or 2 on, some features may be unavailable.

If there is very little low frequency information in the source material, change your

speaker settings to Front: SMALL / Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS

(see Speaker Setting on page 84).

The unit does not respond when the

buttons are pressed.

Try switching the receiver off, then back on again.

Try disconnecting the power cord, then connect again.

AMP ERR blinks in the display, then

the power automatically switches off.

The ADVANCED MCACC blinks and

the power does not turn on.

The receiver may have a serious problem. Do not try switching the receiver on. Unplug the

receiver from the wall and call a Pioneer authorized independent service company.

Symptom Remedy

The receiver suddenly switches off or

the FL OFF indicator blinks.

There is a problem with the receiver’s power unit or fan. Try turning on the power. If the

same thing happens, the receiver is damaged. Unplug the receiver from the wall and call

a Pioneer authorized independent service company. (Other symptoms may appear when

the power is turned on.)

AMP OVERHEAT blinks in the dis-

play and the FL OFF indicator flash

and the power turns off.

Allow the unit to cool down in a well-ventilated place before switching back on (see

Installing the receiver on page 7).

Check whether the cables used to connect the speakers are short-circuited.

Wait at least 1 minute, then try turning the power on again.

The temperature within the unit has exceeded the allowablevalue.

Lower the volume level.

HDZONE cannot be turned on.

Set Output Setting at MAIN/HDZONE to HDZONE (page 88).

No sound

Symptom Remedy

No sound is output when an input

function is selected.

No sound is output from the front

speakers.

Check the volume, mute setting (press MUTE) and speaker setting (press SPEAKERS).

Make sure the correct input function is selected.

Check that the MCACC setup microphone is disconnected.

Make sure the correct input signal is selected (press SIGNAL SEL).

Note that when Fixed PCM ON is selected, you won’t be able to hear any other signal

format (see Setting the Audio options on page 63).

Check that the source component is connected properly (see Connecting your equipment

on page 16).

Check that the speakers are connected properly (see Connecting the speakers on page

19).

No sound from the surround or

center speakers.

Check that the Stereo listening mode or the Front Stage Surround Advance mode isn’t

selected; select one of the surround listening modes (see Enjoying various types of play-

back using the listening modes on page 49).

Check that the surround/center speakers are not set to NO (see Speaker Setting on page

84).

Check the channel level settings (see Channel Level on page 85).

Check the speaker connections (see Connecting the speakers on page 19).

No sound from surround back

speakers.

Check that the surround back speakers are set to LARGE or SMALL, and the surround

speakers are not set to NO (see Speaker Setting on page 84).

Check the speaker connections (see Connecting the speakers on page 19). If only one

surround back speaker is connected, make sure it’s connected to the left channel

speaker terminal.

Surround back speakers will not play while the Speaker System is set to Speaker B and

audio is being played through speaker B.

When Speaker System is set to Normal(SB/FH) or Normal(SB/FW) and SP: FH ON or

SP: FW ON is selected with the SPEAKERS button, no sound will be output from the sur-

round back speakers. Select SP: SB/FH ON, SP: SB/FW ON or SP: SB ON (see Switching

the speaker terminals on page 67).

Pioneer VSX-1123 Seite 92

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-1123

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info