Bedienungsanleitung Pioneer VSX-30 (Seite 93 von 136) (Englisch)

574064

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

The Advanced MCACC menu 10

6 Wait for the Auto MCACC Setup to finish

outputting test tones.

A progress report is displayed on-screen while

the receiver outputs test tones to determine the

speakers present in your setup. Try to be as

quiet as possible while it’s doing this.

• With error messages (such as Too much

ambient noise! or Check microphone)

select RETRY after checking for ambient

noise (see Problems when using the Auto

MCACC Setup on page 44) and verifying the

mic connection. If there doesn’t seem to be

a problem, you can simply select GO NEXT

and continue.

7 If necessary, confirm the speaker

configuration in the GUI screen.

The configuration shown on-screen should

reflect the actual speakers you have.

If no operations are performed for 10 seconds

while the speaker configuration check screen

is being displayed, the Auto MCACC Setup will

resume automatically. In this case, you don’t

need to select ‘OK’ and press ENTER in step 8.

• If you see an ERR message (or the speaker

configuration displayed isn’t correct), there

may be a problem with the speaker

connection.

If selecting RETRY doesn’t work, turn off

the power and check the speaker

connections. If there doesn’t seem to be a

problem, you can simply use / to select

the speaker and / to change the

setting and continue.

•If Reverse Phase is displayed, the

speaker’s wiring (+ and –) may be inverted.

Check the speaker connections.

– If the connections were wrong, turn off

the power, disconnect the power cord, then

reconnect properly. After this, perform the

Full Auto MCACC procedure again.

– If the connections were right, select GO

NEXT and

continue.

8 Make sure ‘

’ is selected, then press

ENTER

A progress report is displayed on-screen while

the receiver outputs more test tones to

determine the optimum receiver settings for

channel level, speaker distance, and Acoustic

Calibration EQ.

Again, try to be as quiet as possible while this

is happening. It may take 3 to 7 minutes.

• If you selected a STAND.WAVE Multi-P

setup (in step 2), you will be asked to place

the mic at the 2nd and 3rd reference points

before finally placing it at your main

listening position.

9 The Auto MCACC Setup procedure is

completed and the

Advanced MCACC

reappears automatically.

The settings made in the Auto MCACC Setup

should give you excellent surround sound from

your system, but it is also possible to adjust

these settings manually using the Manual

MCACC setup menu (starting below) or

Manual SP Setup menu (starting on

page 104).

Note

1 Do not adjust the volume during the test tones. This may result in incorrect speaker settings.

2 This screen is only shown if you selected ALL or Speaker Setting from the Auto MCACC menu.

3 If the speaker is not pointed to the microphone (listening position) or when using speakers that affect the phase

(dipole speakers, reflective speakers, etc.), Reverse Phase may be displayed even if the speakers are properly

connected.

4 • Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12 cm (5

inches) will end up with different size settings. You can correct the setting manually using the Manual speaker setup

on page 104.

• The subwoofer distance setting may be farther than the actual distance from the listening position. This setting

should be accurate (taking delay and room characteristics into account) and generally does not need to be changed.

• If Auto MCACC Setup measurement results are incorrect due to the interaction of the speakers and viewing

environment, we recommend adjusting the settings manually.

VSX-31_30_UC.book 93 ページ２０１０年８月２５日　水曜日　午前９時２８分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-30 Seite 93

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info