Bedienungsanleitung Pioneer VSX-30 (Seite 108 von 136) (Englisch)

574064

108

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

The System Setup and Other Setup menus11

108

1 Select ‘

Speaker Distance

’ from the

Manual SP Setup

menu.

2 Adjust the distance of each speaker using

/

You can adjust the distance of each speaker in

1/2 inch increments.

3 When you’re finished, press

RETURN

You will return to the Manual SP Setup menu.

Tip

• For best surround sound, make sure the

surround back speakers are the same

distance from the listening position.

X-Curve

Most soundtracks mixed for cinema sound too

bright when played back in large rooms. The X-

Curve setting acts as a kind of re-equalization

for home theater listening, and restores proper

tonal balance of movie soundtracks.

1 Select ‘

X-Curve

’ from the

Manual SP

Setup

menu.

2 Choose the X-Curve setting you want.

Use / to adjust the setting. The X-Curve is

expressed as a downwards slope in decibels

per octave, starting at 2 kHz. The sound

becomes less bright as the slope increases (to

a maximum of –3.0dB/oct). Use the following

guidelines to set the X-Curve according to your

room size:

•If you select OFF, the frequency curve will

be flat and the X-Curve has no effect.

3 When you’re finished, press

RETURN

Network Setup menu

Set up the network to listen to Internet radio on

this receiver.

1 Press on the remote control,

then press

HOME MENU

A Graphical User Interface (GUI) screen

appears on your TV. Use /// and

ENTER to navigate through the screens and

select menu items. Press RETURN to confirm

and exit the current menu.

2Select ‘

System Setup

’ from the

Home

3Select ‘

Network Setup

’ from the

System

Setup

menu.

4 Select the setting you want to adjust.

If you are doing this for the first time, you may

want to adjust these settings in order:

• IP Address, Proxy – Sets up the IP

address/Proxy of this receiver (see below).

• Information – Checks the MAC address of

this receiver (page 109).

IP address/Proxy setting

In case the router connected to the LAN

terminal on this receiver is a broadband router

(with a built-in DHCP server function), simply

turn on the DHCP server function, and you will

not need to set up the network manually. You

must set up the network as described below

only when you have connected this receiver to

a broadband router without a DHCP server

function. Before you set up the network,

consult with your ISP or the network manager

for the required settings. It is advised that you

also refer to the operation manual supplied

with your network component.

Note

1 Since the principal is the same, X-Curve isn’t applied when you’re using the Pure direct mode.

Room size (ft

)

≤

400

≤

550

≤

650

≤

800

≤

2200

≤

12000

X-Curve

(dB/oct)

–0.5 –1.0 –1.5 –2.0 –2.5 –3.0

2 In case you make changes to the network configuration without the DHCP server function, make the corresponding

changes to the network settings of this receiver.

RECEIVER

VSX-31_30_UC.book 108 ページ２０１０年８月２５日　水曜日　午前９時２８分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-30 Seite 108

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info