Bedienungsanleitung Pioneer VSX-31 (Seite 118 von 136) (Englisch)

574063

118

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

Additional information12

118

Professional Calibration EQ graphical output

Display

Symptom Remedy

The EQ response displayed in

the graphical output

following calibration does not

appear entirely flat.

• There are cases where the graph does not appear flat (even when selecting

ALL CH ADJ in the Auto MCACC Setup) due to adjustments made to

compensate for room characteristics to achieve optimal sound.

• Areas of the graph may appear identical (before and after) when there is little

or no adjustment needed.

• The graph may appear to have shifted vertically when comparing before and

after measurements.

EQ adjustments made using

the Manual MCACC setup on

page 94 do not appear to

change the graphical output.

• Despite level adjustments being made, the filters used for analysis may not

display these adjustments in the graphical output. However, these adjustments

are taken this into account by the filters dedicated to overall system calibration.

Lower frequency response

curves do not seem to have

been calibrated for SMALL

speakers.

• Low frequencies used in bass management (the subwoofer channel) will not

change for speakers that have been specified as SMALL in the configuration,

or do not output these frequencies.

• Calibration is performed, but due to your speakers’ low frequency limitations,

no measurable sound is output for display.

Symptom Remedy

The display is dark or off. • Press DIMMER repeatedly to select a different brightness.

After making an adjustment

the display goes off.

• Press DIMMER repeatedly to select a different brightness.

You can’t get DIGITAL to

display when using SIGNAL

SEL.

• Check the digital connections and make sure that the digital inputs are

assigned correctly (see The Input Setup menu on page 44).

2 DIGITAL or DTS does not

light when playing Dolby/DTS

software.

• These indicators do not light if playback is paused.

• Check the playback (especially the digital output) settings of the source

component.

When playing Dolby Digital

or DTS sources, the receiver’s

format indicators do not light.

• Check that the player is connected using a digital connection.

• Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the

input signal on page 65).

• Check that the player isn’t set up so that Dolby Digital and DTS sources are

converted to PCM.

• Ensure that if there are several audio tracks on the disc, the Dolby Digital or

DTS is selected.

When playing certain discs,

none of the receiver’s format

indicators light.

• The disc may not contain 5.1/6.1 channel material. Check the disc packaging

for more on what audio tracks are recorded on the disc.

When playing a disc with the

listening mode set to Auto

Surround or ALC, 2 PL II or

Neo:6 appear on the receiver.

• Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the

input signal on page 65).

• If a two channel soundtrack is currently playing (including Dolby Surround

encoded), then this is not a malfunction. Check the disc packaging for details

about the audio tracks available.

VSX-31_30_UC.book 118 ページ２０１０年８月２５日　水曜日　午前９時２８分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-31 Seite 118

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info