Bedienungsanleitung Pioneer VSX-321-K-P (Seite 23 von 64) (Englisch)

574065

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Listening to your system

English

Français

Español

Using surround back channel processing

You can have the receiver automatically use 6.1 or 7.1

decoding for 6.1 encoded sources (for example, Dolby Digital

EX or DTS-ES), or you can choose to always use 6.1 or 7.1

decoding (for example, with 5.1 encoded material). With 5.1

encoded sources, a surround back channel will be

generated, but the material may sound better in the 5.1

format for which it was originally encoded (in which case, you

can simply switch surround back channel processing off).

• With a 7.1-channel surround system, audio signals that

have undergone matrix decoding processing through

surround back channel processing to which the Up Mix

function is added are output from the surround back

speakers.



Press , then press SB CH repeatedly to cycle

the surround back channel options.

Each press cycles through the options as follows:

• SB ON – Matrix decoding processing for generating the

surround back component from the surround component

is turned on.

• SB AUTO – Matrix decoding processing for generating

the surround back component from the surround

component is switched automatically. Matrix decoding

processing is only performed when surround back

channel signals are detected in the input signals.

• SB OFF – Matrix decoding processing for generating the

surround back component from the surround component

is turned off.

Setting the Up Mix function

In a 7.1-channel surround system with surround speakers

placed directly at the sides of the listening position, the

surround sound of 5.1-channel sources is heard from the

side. The Up Mix function mixes the sound of the surround

speakers with the surround back speakers so that the

surround sound is heard from diagonally to the rear as it

should be.

• Using the Up Mix function is effective when the speakers

in the 7.1-channel surround system are set up as

recommended in the example on page 10.

• Depending on the positions of the speakers and the

sound source, in some cases it may not be possible to

achieve good results. In this case, set the setting to OFF.

1 Switch the receiver into standby.

2 While holding down PRESET



on the front panel, and

hold the

 STANDBY/ON

for about two seconds.

UP MIX: OFF appears and the Up Mix function turns off. If

you want to turn this function on, perform steps 1 and 2

again.

• When set to ON, the (Up Mix) indicator on the front

panel lights.

Note

•Set to ON regardless of this setting when playing DTS-HD

signals.

• May automatically be set to OFF even when set to ON,

depending on the input signal and listening mode.

Setting the Audio options

There are a number of additional sound settings you can

make using the AUDIO PARAMETER menu. The defaults, if

not stated, are listed in bold.

Important

• Note that if a setting doesn’t appear in the AUDIO

PARAMETER menu, it is unavailable due to the current

source, settings and status of the receiver.

1 Press , then press AUDIO PARAMETER button.

2Use

/

to select the setting you want to adjust.

Depending on the current status/mode of the receiver,

certain options may not be able to be selected. Check the

table below for notes on this.

3Use

/

to set it as necessary.

See the table below for the options available for each setting.

4 Press RETURN to confirm and exit the menu.

INPUT SELECT

SOURCESLEEP

CONTROL

INPUT

RECEIVER

MIDNIGHT

SPEAKERS

LEV

SB CH

DISP

TEST TONE

CH SELECT

HDD DVD VCR

DTV/TV

RECEIVER

L R

SL SR

SBL SBR SBL SBR

L R

SL SR

UP MIX OFF UP MIX ON

Setting/What it does Option(s)

S.DELAY (Sound Delay)

Some monitors have a slight delay when

showing video, so the soundtrack will be

slightly out of sync with the picture. By adding

a bit of delay, you can adjust the sound to

match the presentation of the video.

0.0 to 9.0

(frames)

1 second = 25

frames (PAL)/30

frames (NTSC)

Default: 0.0

MIDNIGHT/LOUDNESS

The MIDNIGHT allows you to hear effective

surround sound of movies at low volumes.

The LOUDNESS is used to get good bass and

treble from music sources at low volumes.

M/L OFF

MIDNIGHT

LOUDNESS

INPUT SELECT

SOURCESLEEP

CONTROL

INPUT

RECEIVER

BD DVD TV

DTV/TV

ENTER

RETURN

AUDIO

PARAMETER

TUNER EDIT

TOOLS

MASTER

VOLUME

BAND

TOP

HOME

SETUP

RECEIVER

04_listening_your_system.fm 23 ページ２０１１年７月２２日　金曜日　午後６時６分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-321-K-P Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-321-K-P

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info