Bedienungsanleitung Pioneer VSX-321-K-P (Seite 29 von 64) (Englisch)

574065

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Additional information

English

Français

Español

HDMI

No picture or sound.

 If the problem still persists when connecting your HDMI

component directly to your monitor, please consult the

component or monitor manual or contact the manufacturer

for support.

No picture.

 Video signals that are input from the analog video terminal

will not output from the HDMI terminal. Signals that are input

from the HDMI terminal will not output from the analog video

terminal. Be consistent with the type of cable between input

and output.

 Depending in the output settings of the source component, it

may be outputting a video format that can’t be displayed.

Change the output settings of the source, or connect using

the composite jacks.

 This receiver is HDCP-compatible. Check that the components

you are connecting are also HDCP-compatible. If they are not,

please connect them using the composite video jacks.

 Depending on the connected source component, it’s possible

that it will not work with this receiver (even if it is HDCP-

compatible). In this case, connect using the composite video

jacks between source and receiver.

 If video images do not appear on your TV, try adjusting the

resolution, Deep Color or other setting for your component.

 To output signals in Deep Color, use an HDMI cable (High

Speed HDMI

Cable) to connect this receiver to a component

or TV with the Deep Color feature.

No sound, or sound suddenly ceases.

 Check that the Audio Parameter setting is set to HDMI AMP/

THRU (refer to page 23).

 If the component is a DVI device, use a separate connection

for the audio.

 HDMI format digital audio transmissions require a longer time

to be recognized. Due to this, interruption in the audio may

occur when switching between audio formats or beginning

playback.

 Turning on/off the device connected to this unit’s HDMI OUT

terminal during playback, or disconnecting/connecting the

HDMI cable during playback, may cause noise or interrupted

audio.

Important information regarding the HDMI

connection

There are cases where you may not be able to route HDMI

signals through this receiver (this depends on the HDMI

equipped component you are connecting-check with the

manufacturer for HDMI compatibility information).

If you aren’t receiving HDMI signals properly through this

receiver (from your component), please try the following

configuration when connecting up.

Configuration

Connect your HDMI-equipped component directly to the

display using an HDMI cable. Then use the most convenient

connection (digital is recommended) for sending audio to the

receiver. See the operating instructions for more on audio

connections. Set the display volume to minimum when using

this configuration.

Note

• Depending on the component, audio output may be

limited to the number of channels available from the

connected display unit (for example audio output is

reduced to 2 channels for a monitor with stereo audio

limitations).

• If you want to switch the input source, you’ll have to

switch functions on both the receiver and your display

unit.

• Since the sound is muted on the display when using the

HDMI connection, you must adjust the volume on the

display every time you switch input sources.

Resetting the main unit

Use this procedure to reset all the receiver’s settings to the

factory default. Use the front panel controls to do this.

1 Switch the receiver into standby.

2 While holding down BAND, press and hold

 STANDBY/ON

for about two seconds.

3 When you see RESET? appear in the display, press AUTO

SURROUND/STREAM DIRECT.

OK? shows in the display.

4 Press ALC/STANDARD SURR to confirm.

OK appears in the display to indicate that the receiver has

been reset to the factory default settings.

Important

• If the ARC function is ON, you may not be able to initialize

the unit. If this happens, turn OFF the ARC function or

turn OFF all the connected device before turning OFF

(STANDBY) the power for this unit, and initialize after the

HDMI indicator goes out.

Cleaning the unit

• Use a polishing cloth or dry cloth to wipe off dust and dirt.

• When the surface is dirty, wipe with a soft cloth dipped in

some neutral cleanser diluted five or six times with water,

and wrung out well, and then wipe again with a dry cloth.

Do not use furniture wax or cleansers.

• Never use thinners, benzine, insecticide sprays or other

chemicals on or near this unit, since these will corrode

the surface.

07_additional_info.fm 29 ページ２０１１年７月２２日　金曜日　午後６時８分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-321-K-P Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-321-K-P

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info