Bedienungsanleitung Pioneer VSX-517-K (Seite 46 von 63) (Englisch)

574089

Zoom out

Zoom in

Vorherige Seite

1/63

Nächste Seite

The System Setup menu06

If you didn’t make component video

connections according to the defaults above,

you must assign the numbered input to the

component you’ve connected (or else you may

see the video signal of a different component).

For more on this, see

Using the component

video jacks

on page 16.

1 Select COMP. IN from the IN ASSIG. menu.

2 Use

/

to select the number of the

component video input to which you’ve

connected your video component.

The numbers match the numbers beside the

inputs on the back of the receiver.

3 Select the component that corresponds

with the one you connected to that input.

• Use the

/

buttons and

ENTER

to select

DVD

DVR

OFF

• Make sure you have connected the audio

from the component to the corresponding

inputs on the rear of the receiver.

• If you connect any source component to

the receiver using a component video

input, you should also have your TV

connected to this receiver’s

COMPONENT

VIDEO MONITOR OUT

jacks.

The Other setup menu

The Other menu is where you can make

customized settings to reflect how you are

using the receiver.

1 Select OTHER from the System Setup

menu.

2 Use

/

to select the setting you want to

adjust then press

ENTER

If you are doing this for the first time, you may

want to adjust these settings in order:

•

DRC

– Specify the amount of dynamic

range adjustment to Dolby Digital or DTS

soundtracks (see

Dynamic Range Control

Setup

below).

•

DUALMONO

– Isolate one channel when

listening to discs with dual mono encoding

(see

Dual Mono Setup

below).

•

LFE ATT

– Set the attenuator level for the

LFE channel (

LFE Attenuator Setup

below).

3 Use

/

to make the adjustments

necessary for each setting, pressing RETURN

to confirm after each screen.

Dynamic Range Control Setup

• Default setting:

OFF

Specifies the amount of dynamic range

adjustment to Dolby Digital or DTS

soundtracks:

•

DRC OFF

– No dynamic range adjustment

(use when listening at higher volume).

•

DRC MAX

– Dynamic range is reduced

(loud sounds are reduced in volume while

quieter sounds are increased).

•

DRC MID

– Mid setting.

Dual Mono Setup

• Default setting:

CH1

Specifies how dual mono encoded Dolby

Digital soundtracks should be played:

•

CH1

– Only channel 1 is played

•

CH2

– Only channel 2 is played

•

CH1 CH2

– Both channels are played

through the front speakers

LFE Attenuator Setup

• Default setting:

ATT 0 dB

Set the LFE attenuator as necessary to prevent

ultra-low bass tones (included with some

Dolby Digital and DTS audio sources) from

distorting the sound from the speakers:

•

LFEATT 0

– No limiting (recommended

setting)

•

LFEATT 10

– 10 dB of limiting

•

LFEATT **

– No sound from LFE channel

Note

1 This setting works only with dual mono encoded Dolby Digital and DTS soundtracks.

VSX517_817.fm 46 ページ２００７年２月２２日　木曜日　午後８時１１分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-517-K Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-517-K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info