Bedienungsanleitung Pioneer VSX-531D (Seite 27 von 41) (Englisch)

699667

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

Listening to your system

Using the Advanced Sound Retriever

When audio data is removed during the compression

process, sound quality often suffers from an uneven sound

image. The Advanced Sound Retriever feature employs new

DSP technology that helps bring CD quality sound back to

compressed 2-channel audio by restoring sound pressure

and smoothing jagged artifacts left over after compression.

…

Press

S.RETRIEVER

to switch the S.RTV (Advanced

Sound Retriever) ON or OFF.

Note

• The Advanced Sound Retriever mode cannot be set to

when the

DIRECT

mode or the

PURE DIRECT

mode is

switched on.

Better sound using Phase Control

This receiver’s Phase Control feature uses phase correction

measures to make sure your sound source arrives at the

listening position in phase, preventing unwanted distortion

and/or coloring of the sound.

Phase Control technology provides coherent sound

reproduction through the use of phase matching for an

optimal sound image at your listening position. The default

setting is on and we recommend leaving Phase Control

switched on for all sound sources.

…

Press

PHASE

to switch the P.CTL (Phase Control) ON

or OFF.

Note

• Phase matching is a very important factor in achieving proper

sound reproduction. If two waveforms are ‘in phase’, they

crest and trough together, resulting in increased amplitude,

clarity and presence of the sound signal. If a crest of a wave

meets a trough, then the sound will be ‘out of phase’ and an

unreliable sound image will be produced.

•

If your subwoofer has a phase control switch, set it to the

plus (+) sign (or 0°). However, the effect you can actually

feel when Phase Control is set to ON on this receiver

depends on the type of your subwoofer. Set your

subwoofer to maximize the effect. It is also recommended

you try changing the orientation or the place of your

subwoofer.

•

Set the built-in lowpass filter switch of your subwoofer to

OFF. If this cannot be done on your subwoofer, set the

cutoff frequency to a higher value.

•

If the speaker distance is not properly set, you may not

have a maximized Phase Control effect.

•

The Phase Control mode cannot be set to ON in the

following cases:

When the PURE DIRECT mode is switched on.

When the headphones are connected.

Setting the Audio options

There are a number of additional sound settings you can

make using the AV ADJUST menu. The defaults, if not

stated, are listed in bold.

Important

•

Note that if a setting doesn’t appear in the AV ADJUST

menu, it is unavailable due to the current source, settings

and status of the receiver.

Press

AV ADJUST

button.

Use





to select the setting you want to adjust.

Depending on the current status/mode of the receiver,

certain options may not be able to be selected. Check

the table below for notes on this.

Use





to set it as necessary.

See the table below for the options available for each

setting.

Press

RETURN

to confirm and exit the menu.

PHASEPHASEPHASEPHASE

S.RETRIEVERS.RETRIEVER

BT AUDIOBT AUDIO

BASSBASS

USBUSBTUNTUN

AUXAUX

BTBT

ADJUST

MUTE

HOME

RETURN

RETURNRETURN

RETURN

VOLUME

Setting/What it does Option(s)

EQ (Acoustic Calibration EQ)

Switches on/off the effect of Acoustic

Calibration EQ.

OFF

S.DLY (Sound Delay)

Some monitors have a slight delay when

showing video, so the soundtrack will be

slightly out of sync with the picture. By adding

a bit of delay, you can adjust the sound to

match the presentation of the video.

0 ms to 500 ms

(1 step : 5 ms)

Default: 0

MIDNIGHT/LOUDNESS

The MIDNIGHT allows you to hear effective

surround sound of movies at low volumes.

The

LOUDNESS

is used to get good bass and

treble from music sources at low volumes.

M/L OFF

MIDNIGHT

LOUDNESS

S.RTV (Advanced Sound Retriever)

Switches on/off the effect of Advanced Sound

Retriever. (see Using the Advanced Sound

Retriever above)

OFF

DUAL MONO

Specifies how dual mono encoded Dolby

Digital soundtracks should be played.

CH1 – Channel 1

is heard only

CH2 – Channel 2

is heard only

CH1 CH2 – Both

channels heard

from front

speakers

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-531D Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-531D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info