Bedienungsanleitung Pioneer VSX-815-K (Seite 49 von 76) (Englisch)

574180

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

The System Setup menu

English

Français

Deutsch

Nederlands

Italiano

Español

output bass sound continuously or you

want deeper bass (the bass frequencies

that would normally come out the front and

center speakers are also routed to the

subwoofer). If you did not connect a

subwoofer choose

(the bass

frequencies are output from other

speakers).

3 When you’re finished, press RETURN.

Tip

• If you have a subwoofer and like lots of

bass, it may seem logical to select

LARGE

for your front speakers and

PLUS

for the

subwoofer. This may not, however, yield the

best bass results. Depending on the

speaker placement of your room you may

actually experience a decrease in the

amount of bass due low frequency

cancellations. In this case, try changing

the position or direction of speakers. If you

can’t get good results, listen to the bass

response with it set to

PLUS

and

YES

or the

front speakers set to

LARGE

and

SMALL

alternatively and let your ears judge which

sounds best. If you’re having problems, the

easiest option is to route all the bass

sounds to the subwoofer by selecting

SMALL

for the front speakers.

Crossover network

• Default setting:

100Hz

This setting decides the cutoff between bass

sounds playing back from the speakers

selected as

LARGE

, or the subwoofer, and bass

sounds playing back from those selected as

SMALL

It also decides where the cutoff will

be for bass sounds in the LFE channel.

1 Select ‘

X.OVER’

from the SP SETUP menu.

2 Use

/

(cursor up/down) to choose the

frequency cutoff point.

Frequencies below the cutoff point will be sent

to the subwoofer (or

LARGE

speakers).

3 When you’re finished, press RETURN.

Channel level

Using the channel level settings, you can

adjust the overall balance of your speaker

system, an important factor when setting up a

home theater system.

1 Select

CH LEVEL

from the SP SETUP menu.

2 Use

/

(cursor up/down) to select a

setup option.

•

T. TONE M.

– Move the test tone manually

from speaker to speaker and adjust

individual channel levels.

•

T. TONE A.

– Adjust channel levels as the

test tone moves from speaker to speaker

automatically.

3 Confirm your selected setup option.

The test tones will start after you press

ENTER

4 Adjust the level of each channel using the

/

(cursor up/down) buttons.

If you selected

T. TONE M.

, use

/

(cursor

left/right) to switch speakers.

The

T. TONE A.

setup will output test tones in

the following order (depending on the speaker

setting):

Note

2• If the surround speakers are set to

, the surround back speakers will automatically be set to

• If you selected

SB 2ND Z

SB BIAMP

(in

Surround back speaker setting

on page 43) you can’t adjust the surround back

settings.

• If you select one surround back speaker only, make sure that speaker is hooked up to the left surround back terminal.

1 For more on selecting the speaker sizes, see

Speaker setting

above.

SBR

SW SBL

VSX_815-915.book.fm 49 ページ２００４年１２月８日　水曜日　午後４時３分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-815-K Seite 49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info