Bedienungsanleitung Pioneer VSX-818V (Seite 9 von 76) (Englisch)

794003

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

5 minute guide 02

English Français

Deutsch

Nederlands

Italiano Español

5 Follow the instructions on-screen.

• Make sure the microphone is connected.

• If you’re using a subwoofer, it is

automatically detected every time you

switch on the system. Make sure it is on

and the volume is turned up.

•See below for notes regarding background

noise and other possible interference.

6 Wait for the test tones to finish.

A progress report is displayed on-screen while

the receiver outputs test tones to determine the

speakers present in your setup. Try to be as

quiet as possible while it’s doing this.

•For correct speaker settings, do not adjust

the volume during the test tones.

7 Confirm the speaker configuration.

The configuration shown on-screen should

reflect the actual speakers you have.

If the speaker configuration displayed isn’t

correct, use

/

to select the speaker and

/

to change the setting. When you’re

finished, go to the next step.

If you see an error message (

ERR

) in the right

side column, there may be a problem with the

speaker connection. If selecting

RETRY

doesn’t fix the problem, turn off the power and

check the speaker connections.

8 Make sure ‘OK’ is selected, then press

ENTER.

If the screen in step 7 is left untouched for 30

seconds and the

ENTER

button is not pressed

in step 8, the Auto MCACC setup will start

automatically as shown below.

A progress report is displayed on-screen while

the receiver outputs more test tones to

determine the optimum receiver settings for

channel level, speaker distance, and Acoustic

Calibration EQ.

Again, try to be as quiet as possible while this

is happening. It may take 3 to 8 minutes.

9 The Auto MCACC Setup has finished!

Select ‘SKIP’ to go back to the System

Setup menu.

The MCACC indicator on the front panel will

light to show the setup is complete.

The settings made in the Auto MCACC Setup

should give you excellent surround sound

from your system, but it is also possible to

adjust these settings manually using the

System Setup menu (starting on page 37).

1.Auto MCACC

Now Analyzing

Environment Check

Ambient Noise [ OK ]

Microphone [ ]

Speaker YES/NO [ ]

:Cancel

1.Auto MCACC

Check!

Front [ YES ]

Center [ YES ]

Surround [ YES ]

SUB W. [ YES ]

:Cancel

30:Next

Note

1• Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12 cm (5 inches)

will end up with different size settings. You can correct the setting manually using the

Speaker Setting

on page 42.

• The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be

accurate (taking delay and room characteristics into account) and generally does not need to be changed.

1.Auto MCACC

Now Analyzing

Surround Analyzing

Speaker System [ ]

Speaker Distance [ ]

Channel Level [ ]

Acoustic Cal EQ [ ]

:Cancel

VSX_918_818_KU.book 9 ページ２００７年１１月２８日　水曜日　午後６時５８分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-818V Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info