Bedienungsanleitung Pioneer VSX-820-K (Seite 30 von 228) (Englisch, Französisch, Spanisch)

574197

Zoom out

Zoom in

Vorherige Seite

1/228

Nächste Seite

Basic Setup04

3 Press on the remote control,

then press the

SETUP

button.

An on-screen display (OSD) appears on your

TV. Use /// and ENTER on the remote

control to navigate through the screens and

select menu items. Press RETURN to exit the

current menu.

• Press SETUP at any time to exit the System

Setup menu.

4 Select ‘Auto MCACC’ from the System

Setup menu then press ENTER.

Try to be as quiet as possible after pressing

ENTER. The system outputs a series of test

tones to establish the ambient noise level.

5 Follow the instructions on-screen.

• Make sure the microphone is connected.

• Make sure the subwoofer is on and the

volume is turned up.

• See below for notes regarding background

noise and other possible interference.

6 Wait for the test tones to finish.

A progress report is displayed on-screen while

the receiver outputs test tones to determine the

speakers present in your setup. Try to be as

quiet as possible while it’s doing this.

• For correct speaker settings, do not adjust

the volume during the test tones.

7 Confirm the speaker configuration.

The configuration shown on-screen should

reflect the actual speakers you have.

• With error messages (such as Too much

ambient noise) select RETRY after

checking for ambient noise (see Other

problems when using the Auto MCACC

Setup on page 31).

If the speaker configuration displayed isn’t

correct, use / to select the speaker and

/ to change the setting. When you’re

finished, go to the next step.

If you see an error message (ERR) in the right

side column, there may be a problem with the

speaker connection. If selecting RETRY

doesn’t fix the problem, turn off the power and

check the speaker connections.

8 Make sure ‘OK’ is selected, then press

ENTER.

If the screen in step 7 is left untouched for 10

seconds and the ENTER button is not pressed

in step 8, the Auto MCACC setup will start

automatically as shown below.

A progress report is displayed on-screen while

the receiver outputs more test tones to

determine the optimum receiver settings for

channel level, speaker distance, and Acoustic

Calibration EQ.

Note

1 The screensaver automatically starts after three minutes of inactivity. If you cancel the Auto MCACC Setup at any time, the

receiver automatically exits and no settings will be made.

2 MIC IN blinks when the microphone is not connected to MCACC SETUP MIC.

RECEIVER

System Setup

1.Auto MCACC

2.Manual SP Setup

3.Input Assign

4.Pre Out Setting

Return

1.Auto MCACC

Now Analyzing

Environment Check

Ambient Noise

Speaker YES/NO

Return

1.Auto MCACC

Check!

Return

10:Next

Front

Center

Surr

Surr. Back

Subwoofer

[ YES ]

[YESx2]

[ YES ]

1.Auto MCACC

Now Analyzing

Surround Analyzing

Speaker System

Speaker Distance

Channel Level

Acoustic Cal EQ

Return

VSX-820_UCSMXCN_En.book 30 ページ２００９年１２月２１日　月曜日　午後４時１７分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-820-K Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-820-K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info