Bedienungsanleitung Pioneer VSX-820-K (Seite 69 von 228) (Englisch, Französisch, Spanisch)

574197

Zoom out

Zoom in

Vorherige Seite

1/228

Nächste Seite

Additional information 11

English

Français

Deutsch

Nederlands

Italiano

Español

No sound from surround or

center speakers.

• Connect the speakers properly (refer to page 18).

• Refer to Speaker Setting on page 43 to check the speaker settings.

• Refer to Channel Level on page 45 to check the speaker levels.

The PHASE CONTROL

feature doesn’t seem to

have an audible effect.

• If applicable, check that the lowpass filter switch on your subwoofer is

off, or the lowpass cutoff is set to the highest frequency setting. If there is

a PHASE setting on your subwoofer, set it to 0º (or depending on the

subwoofer, the setting where you think it has the best overall effect on the

sound).

• Make sure the speaker distance setting is correct for all speakers (see

Speaker Distance on page 46).

Considerable noise in radio

broadcasts.

• Connect the antenna (page 27) and adjust the position for best

reception.

• Route any loose cables away from the antenna terminals and wires.

• Fully extend the FM wire antenna, position for best reception, and

secure to a wall (or connect an outdoor FM antenna).

• Connect an additional internal or external AM antenna (page 27).

• Turn off equipment causing interference or move it away from the

receiver (or move antennas farther away from equipment causing noise).

Broadcast stations cannot

be selected automatically.

• Connect an outdoor antenna (refer to page 27).

Noise during playback of a

cassette deck.

• Move the cassette deck away from your receiver, until the noise

disappears.

Sound is produced from

other components, but not

from LD or DVD player.

• Set the SIGNAL SEL to HDMI, C1/O1/O2 (DIGITAL) or A (analog)

according to the type of connections made (refer to page 41).

• Set the digital input settings correctly (refer to page 46).

•

Make digital connections (refer to page 23) and set the

SIGNAL SEL

C1/O1/O2 (DIGITAL)

(refer to page 41).

• Refer to the instruction manual supplied with the DVD player.

No sound is output or a

noise is output when

software with DTS is played

back.

• Set the digital volume level of the player to full, or to the neutral

position.

• Make sure the player’s settings are correct and/or the DTS signal out is

on. Refer to the instruction manual supplied with the DVD player.

• Set the input signal type to C1/O1/O2 (DIGITAL) (see Choosing the

input signal on page 41).

During a playback search,

noise is output from a DTS

compatible CD player.

• This is not a malfunction, but be sure to turn the volume down to

prevent the output of loud noise from your speakers.

Everything seems to be set

up correctly, but the

playback sound is odd.

• Check that the positive/negative speaker terminals on the receiver are

matched with the corresponding terminals on the speakers (see

Connecting the speakers on page 18).

Problem Remedy

VSX-820_UCSMXCN_En.book 69 ページ２００９年１２月２１日　月曜日　午後４時１７分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-820-K Seite 69

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-820-K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info