Bedienungsanleitung Pioneer VSX-824 (Seite 61 von 69) (Englisch)

548142

Zoom out

Zoom in

Vorherige Seite

1/69

Nächste Seite

Chapter

Additional information

Troubleshooting

Incorrect operations are often mistaken for trouble and

malfunctions. If you think that there is something wrong with

this component, check the points below. Take a look at the

other components and electrical appliances being used,

because sometimes the problem may lie there. If the trouble

isn’t sorted out even after going through the checks below,

ask your nearest Pioneer authorized independent service

company to carry out repair work.

•

If the unit does not operate normally due to external effects

such as static electricity disconnect the power plug from

the outlet and insert again to return to normal operating

conditions.

General

 The power does not turn on.

 Disconnect the power plug from the outlet, and insert again.

 Make sure there are no loose strands of speaker wire touching

the rear panel. This could cause the receiver to shut off

automatically.

 The receiver suddenly switches off.

 When the Auto Power Down function is working, the power will

automatically turn off if the receiver has not operated for

several hours. Check the setting for the Auto Power Down

function (see The Auto Power Down menu on page 56).

 After about a minute (you won’t be able to switch the unit on

during this time), switch the receiver back on. If the message

persists, call a Pioneer authorized independent service

company.

 If there is very little low frequency information in the source

material, change your speaker settings to Front: SMALL /

Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS (page 53).

 The HDMI indicator blinks and the power does not turn

on.

 The receiver may have a serious problem. Do not try switching

the receiver on. Unplug the receiver from the wall and call a

Pioneer authorized independent service company.

 The power suddenly turns on or off, or the input suddenly

changes (When the Control with HDMI is ON).

 This happens because of the synchronized operation due to

the Control with HDMI function. If synchronized operations

are not needed, set the Control with HDMI to OFF (see HDMI

Setup on page 59).

 OVERHEAT shows in the display and the power turns off.

 The temperature within the unit has exceeded the allowable

value. Try moving the unit for better ventilation (page 2).

 Lower the volume level.

 TEMP shows in the display and the volume level drops.

 The temperature within the unit has exceeded the allowable

value. Try moving the unit for better ventilation (page 2).

 Lower the volume level.

 No sound is output when an input function is selected.

 Use

VOLUME +/–

to turn up the volume.

 Press

MUTE

on the remote control to turn muting off.

 Press

SP-A/B

to select the proper speaker set (see Switching

the speaker terminal on page 18).

 Set the

SIGNAL SEL

to H (HDMI), C1/O1 (digital) or A (analog)

according to the type of connections made (page 28).

 Make sure the component is connected correctly (refer to

Connecting your equipment on page 14).

 Check the audio output settings of the source component.

 Refer to the instruction manual supplied with the source

component.

 No image is output when an input function is selected.

 Make sure the component is connected correctly (refer to

Connecting your equipment on page 14).

 Use the same type of video cables for the source component

and TV to connect to this receiver (see About video outputs

connection on page 19).

 VSX-1029 only: Check The Input Assign menu on page 55 to

make sure you’re assigned the correct input.

 The video input selected on the TV monitor is incorrect. Refer

to the instruction manual supplied with the TV.

 No sound from subwoofer.

 Make sure the subwoofer is switched on.

 If the subwoofer has a volume knob, make sure it’s turned up.

 The Dolby Digital or DTS source you are listening to may not

have an LFE channel.

 Switch the subwoofer setting in Speaker Setting on page 53 to

YES or PLUS.

 Switch the LFE ATT (LFE Attenuate) on page 40 to LFEATT 0 or

LFEATT 5.

 No sound from surround or center speakers.

 Connect the speakers properly (page 15).

 Refer to Speaker Setting on page 53 to check the speaker

settings.

 Refer to Channel Level on page 54 to check the speaker levels.

 The OSD screen (Home Menu, etc.) isn’t displayed.

 The OSD will not appear if you have connected using the

composite output to your TV. Use HDMI connection when

setting up the system.

 The Phase Control feature doesn’t seem to have an

audible effect.

 If applicable, check that the lowpass filter switch on your

subwoofer is off, or the lowpass cutoff is set to the highest

frequency setting. If there is a PHASE setting on your

subwoofer, set it to 0º (or depending on the subwoofer, the

setting where you think it has the best overall effect on the

sound).

 Make sure the speaker distance setting is correct for all

speakers (see Speaker Distance on page 55).

 Considerable noise in radio broadcasts.

 Connect the antenna (page 23) and adjust the position for best

reception.

 Route any loose cables away from the antenna terminals and

wires.

 Fully extend the FM wire antenna, position for best reception,

and secure to a wall (or connect an outdoor FM antenna).

 Connect an additional internal or external AM antenna

(page 23).

 Turn off equipment causing interference or move it away from

the receiver (or move antennas farther away from equipment

causing noise).

 Broadcast stations cannot be selected automatically.

 Connect an outdoor antenna (page 23).

 Noise during playback of a cassette deck.

 Move the cassette deck away from your receiver, until the noise

disappears.

 No sound is output or a noise is output when software

with DTS is played back.

 Make sure the player’s settings are correct and/or the DTS

signal out is on. Refer to the instruction manual supplied with

the DVD player.

 There seems to be a time lag between the speakers and

the output of the subwoofer.

 See Automatically setting up for surround sound (MCACC) on

page 26 to set up your system again using MCACC (this will

automatically compensate for a delay in the subwoofer output).

 After using the Auto MCACC setup, the speaker size

setting (LARGE or SMALL) is incorrect.

 Low-frequency noise could have been caused by an air

conditioner or motor. Switch off all appliances in the room and

rerun the Auto MCACC setup.

Pioneer VSX-824 Seite 61

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-824

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info