Bedienungsanleitung Pioneer VSX-827-K (Seite 12 von 68) (Englisch)

491882

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Connecting your equipment

•

Surround and surround back speakers should be

positioned 60 cm to 90 cm higher than your ears and titled

slight downward. Make sure the speakers don’t face each

other. For DVD-Audio, the speakers should be more directly

behind the listener than for home theater playback.

•

Try not to place the surround speakers farther away from

the listening position than the front and center speakers.

Doing so can weaken the surround sound effect.

•

Place the left and right front height speakers at least one

meter directly above the left and right front speakers.

•

If you’re going to place speakers around your CRT TV, use

shielded speakers or place the speakers at a sufficient

distance from your CRT TV.

•

The subwoofer can be placed on the floor. Ideally, the other

speakers should be at about ear-level when you’re listening

to them. Putting the speakers on the floor (except the

subwoofer), or mounting them very high on a wall is not

recommended.

•

When not connecting a subwoofer, connect speakers with

low frequency reproduction capabilities to the front

channel. (The subwoofer’s low frequency component is

played from the front speakers, so the speakers could be

damaged.)

•

After connecting, be sure to conduct the Auto MCACC

(speaker environment setting) procedure.

See Automatically setting up for surround sound (MCACC)

on page 23.

CAUTION

•

Make sure that all speakers are securely installed. This not

only improves sound quality, but also reduces the risk of

damage or injury resulting from speakers being knocked

over or falling in the event of external shocks such as

earthquakes.

Connecting the speakers

The receiver will work with just two stereo speakers (the front

speakers in the diagram) but using at least three speakers is

recommended, and a complete setup is best for surround

sound.

Make sure you connect the speaker on the right to the right (R)

terminal and the speaker on the left to the left (L) terminal.

Also make sure the positive and negative (+/–) terminals on

the receiver match those on the speakers.

You can use speakers with a nominal impedance between 6 Ω

and 16 Ω.

Be sure to complete all connections before connecting this unit

to the AC power source.

Bare wire connections

Twist exposed wire strands together.

Loosen terminal and insert exposed wire.

Tighten terminal.

Connect the wires to the B-Speakers terminals of the VSX-827 as

shown below:

Twist exposed wire strands together.

Push open the tabs and insert exposed wire.

Release the tabs.

CAUTION

•

These speaker terminals carry HAZARDOUS LIVE voltage.

To prevent the risk of electric shock when connecting or

disconnecting the speaker cables, disconnect the power

cord before touching any uninsulated parts.

•

Make sure that all the bare speaker wire is twisted together

and inserted fully into the speaker terminal. If any of the

bare speaker wire touches the back panel it may cause the

power to cut off as a safety measure.

Connect the surround back or front height

speakers (In case of VSX-827)

The Speaker System setting must be set if the above

connections are performed. Select Surr.Back if the surround

back speaker is connected and Height if the front height

speaker is connected (If neither the surround back speaker

nor the front height speaker is connected, either setting will

suffice) (see The Speaker System setting (VSX-827 only)

page 50).

•

When using only one surround back speaker, connect it to

the SURROUND BACK L (Single) terminals.

Connect the surround back or front height

speakers (In case of VSX-527)

Connect the PRE OUT SURR BACK/FRONT HEIGHT outputs

of the unit and additional amplifier to add a surround back or

front height speaker.

The Pre Out setting must be set if the above connections are

performed. Select Surr.Back if the surround back speaker is

connected and Height if the front height speaker is

connected (If neither the surround back speaker nor the front

height speaker is connected, either setting will suffice) (see

The Pre Out Setting (VSX-527 only)

on page 51).

•

You can use the additional amplifier on the surround back

channel pre-outs for a single speaker as well. In this case

plug the amplifier into the left (L (Single)) terminal only.

12 3

10 mm

12 3

10 mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-827-K Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-827-K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info