Bedienungsanleitung Pioneer VSX-827-K (Seite 48 von 68) (Englisch)

491882

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Home Menu

Select ‘Manual SP Setup’ from the Home Menu.

Select ‘Speaker Setting’ from the Manual SP Setup

menu.

Choose the set of speakers that you want to set then

select a speaker size.

Use

/

to select the size (and number) of each of the

following speakers:

•

Front – Select LARGE if your front speakers reproduce bass

frequencies effectively, or if you didn’t connect a

subwoofer. Select SMALL to send the bass frequencies to

the subwoofer.

•

Center – Select LARGE if your center speaker reproduces

bass frequencies effectively, or select SMALL to send bass

frequencies to the other speakers or subwoofer. If you

didn’t connect a center speaker, choose NO (the center

channel is sent to the other speakers).

•

Front Height – Select LARGE if your front height speakers

reproduce bass frequencies effectively. Select SMALL to

send bass frequencies to the other speakers or subwoofer.

If you didn’t connect front height speakers choose NO.

You can only adjust the Front Height setting when Pre

Out Setting is set to Height.

•

Surr – Select LARGE if your surround speakers reproduce

bass frequencies effectively. Select SMALL to send bass

frequencies to the other speakers or subwoofer. If you

didn’t connect surround speakers choose NO (the sound of

the surround channels is sent to the other speakers).

•

Surr. Back – Select the number of surround back speakers

you have (one, two or none). Select LARGE if your surround

back speakers reproduce bass frequencies effectively.

Select SMALL to send bass frequencies to the other

speakers or subwoofer. If you didn’t connect surround back

speakers choose NO.

VSX-527 only: You can only adjust the Surr. Back setting

when Pre Out Setting is set to Surr. Back.

VSX-527 only: If you select one surround back speaker

only, make sure that additional amplifier is hooked up to

the PRE OUT L (Single) terminal.

VSX-827 only: When using only one surround back

speaker, connect it to the SURROUND BACK L (Single)

terminals.

•

Subwoofer – LFE signals and bass frequencies of

channels set to SMALL are output from the subwoofer

when YES is selected (see notes below). Choose the PLUS

setting if you want the subwoofer to output bass sound

continuously or you want deeper bass (the bass

frequencies that would normally come out the front and

center speakers are also routed to the subwoofer). If you did

not connect a subwoofer choose NO (the bass frequencies

are output from other speakers).

When you’re finished, press

RETURN

You return to the Manual SP Setup menu.

Note

•

If you select SMALL for the front speakers, the subwoofer

will automatically be fixed to YES. Also, the center,

surround, surround back and front height speakers can’t

be set to LARGE if the front speakers are set to SMALL. In

this case, all bass frequencies are sent to the subwoofer.

•

If the surround speakers are set to NO, the surround back

speakers will automatically be set to NO.

•

If you have a subwoofer and like lots of bass, it may seem

logical to select LARGE for your front speakers and PLUS

for the subwoofer. This may not, however, yield the best

bass results. Depending on the speaker placement of your

room you may actually experience a decrease in the

amount of bass due to low frequency cancellations. In this

case, try changing the position or direction of speakers. If

you can’t get good results, listen to the bass response with

it set to PLUS and YES or the front speakers set to LARGE

and SMALL alternatively and let your ears judge which

sounds best. If you’re having problems, the easiest option

is to route all the bass sounds to the subwoofer by selecting

SMALL for the front speakers.

X.Over

•

Default setting: 100Hz

This setting decides the cutoff between bass sounds playing

back from the speakers selected as LARGE, or the subwoofer,

and bass sounds playing back from those selected as SMALL.

It also decides where the cutoff will be for bass sounds in the

LFE channel.

•

For more on selecting the speaker sizes, see Speaker Setting

on page 47.

Select ‘Manual SP Setup’ from the Home Menu.

Select ‘X.Over’ from the Manual SP Setup menu.

Choose the frequency cutoff point.

Frequencies below the cutoff point will be sent to the

subwoofer (or LARGE speakers).

When you’re finished, press

RETURN

You return to the Manual SP Setup menu.

. Manual SP Setup

Return

. Speaker Setting

. X.Over

. Channel Level

. Speaker Distance

. Speaker Setting

Front

Center

Surr

Surr. Back

Subwoofer:

Return

[ SMALL ]

[ NO

]

YES

SMALL

. Manual SP Setup

Return

. Speaker Setting

. X.Over

. Channel Level

. Speaker Distance

. X.Over

Return

Frequency 100Hz

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-827-K Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-827-K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info