Bedienungsanleitung Pioneer VSX-828 (Seite 12 von 71) (Englisch)

536837

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

Connecting your equipment

Some tips for improving sound quality

Where you put your speakers in the room has a big effect on

the quality of the sound. The following guidelines should help

you to get the best sound from your system.

•

It is best to angle the speakers towards the listening

position. The angle depends on the size of the room. Use

less of an angle for bigger rooms.

•

Refer to the chart below for placement of speakers you

intend to connect.

Place the surround speakers at 120º from the center. If

you, (1) use the surround back speaker, and, (2) don’t use

the front height speakers, we recommend placing the

surround speaker right beside you.

If you intend to connect only one surround back

speakers, place it directly behind you.

If the surround speakers cannot be set directly to the side

of the listening position with a 7.1-channel system, the

surround effect can be enhanced by turning off the Up

Mix function (see Setting the Up Mix function (VSX-828

only) on page 40).

•

For the best stereo effect, place the front speakers 2 m to

3 m apart, at equal distance from the TV.

•

If you’re using a center speaker, place the front speakers at

a wider angle. If not, place them at a narrower angle.

•

Place the center speaker above or below the TV so that the

sound of the center channel is localized at the TV screen.

Also, make sure the center speaker does not cross the line

formed by the leading edge of the front left and right

speakers.

•

Surround and surround back speakers should be

positioned 60 cm to 90 cm higher than your ears and titled

slight downward. Make sure the speakers don’t face each

other. For DVD-Audio, the speakers should be more directly

behind the listener than for home theater playback.

•

Try not to place the surround speakers farther away from

the listening position than the front and center speakers.

Doing so can weaken the surround sound effect.

•

Place the left and right front height speakers at least one

meter directly above the left and right front speakers.

•

If you’re going to place speakers around your CRT TV, use

shielded speakers or place the speakers at a sufficient

distance from your CRT TV.

•

The subwoofer can be placed on the floor. Ideally, the other

speakers should be at about ear-level when you’re listening

to them. Putting the speakers on the floor (except the

subwoofer), or mounting them very high on a wall is not

recommended.

•

When not connecting a subwoofer, connect speakers with

low frequency reproduction capabilities to the front

channel. (The subwoofer’s low frequency component is

played from the front speakers, so the speakers could be

damaged.)

•

After connecting, be sure to conduct the Auto MCACC

(speaker environment setting) procedure.

See Automatically setting up for surround sound (MCACC)

on page 24.

CAUTION

•

Make sure that all speakers are securely installed. This not

only improves sound quality, but also reduces the risk of

damage or injury resulting from speakers being knocked

over or falling in the event of external shocks such as

earthquakes.

Connecting the speakers

The receiver will work with just two stereo speakers (the front

speakers in the diagram) but using at least three speakers is

recommended, and a complete setup is best for surround

sound.

Make sure you connect the speaker on the right to the right (R)

terminal and the speaker on the left to the left (L) terminal.

Also make sure the positive and negative (+/–) terminals on

the receiver match those on the speakers.

You can use speakers with a normal impedance between 6 

and 16 .

Be sure to complete all connections before connecting this unit

to the AC power source.

Bare wire connections

Twist exposed wire strands together.

Loosen terminal and insert exposed wire.

Tighten terminal.

Connect the wires to the B-Speakers terminals of the VSX-828 as

shown below:

Twist exposed wire strands together.

Push open the tabs and insert exposed wire.

Release the tabs.

FHL

SBL

SBR

FHR

30 30

120 120

12 3

10 mm

12 3

10 mm

VSX-828_SYXE8_En.book 12 ページ２０１３年３月１日　金曜日　午前９時１６分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-828 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-828

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info