586462

Pioneer VSX-830 K Seite 115

115
Zoom out
Zoom in
Vorherige Seite
1/137
Nächste Seite
115
FAQ
14
Symptom Remedy
VSX-1130 only: No sound from sur-
round back speakers.
Check that the surround back speakers are set to LARGE or SMALL, and the surround
speakers are not set to NO (see Speaker Setting on page 107 ).
Check the speaker connections (see Connecting the speakers on page 24 ). If only
one surround back speaker is connected, make sure it’s connected to the left channel
speaker terminal.
When Speaker System is set to 7.2ch/5.2.2ch and SP: TMd ON is selected with the
OUT P. button, no sound will be output from the surround back speakers. Select SP:
SB ON or SP: SB/TMd ON (see Switching the speaker terminals on page 88 ).
When Speaker System is set to 7.2ch SB/FW and SP: FW ON is selected with the OUT P.
button, no sound will be output from the surround back speakers. Select SP: SB ON or
SP: SB/FW ON (see Switching the speaker terminals on page 88 ).
When Dolby Surround is selected, audio is not output from the surround back speaker
when it is the only one connected (set).
VSX-1130 only: No sound from front
wide speakers.
Check that the front wide speakers are set to LARGE or SMALL, and the surround speak-
ers are not set to NO (see Speaker Setting on page 107 ).
Check the speaker connections (see Connecting the speakers on page 24 ).
When Speaker System is set to 7.2ch SB/FW and SP: SB ON is selected with the OUT P.
button, no sound will be output from the front wide speakers. Select SP: FW ON or SP:
SB/FW ON (see Switching the speaker terminals on page 88 ).
When Speaker System is set to 7.2ch SB/FW and Dolby Surround is selected, audio is
not output from the front wide speakers.
No sound from subwoofer. Check that the subwoofer is connected properly, switched on and the volume turned up.
If your subwoofer has a sleep function, make sure it is switched off.
Make sure that the Subwoofer setting is YES or PLUS (see Speaker Setting on page 107 ).
The crossover frequency may be set too low; try setting it higher to match the characteris-
tics of your other speakers (see Speaker Setting on page 107 ).
If there is very little low frequency information in the source material, change your
speaker settings to Front: SMALL / Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS
(see Speaker Setting on page 107 ).
Check that the LFE channel is not set to OFF, or to a very quiet setting (see Setting the
Audio options on page 86 ).
Check the speaker level settings (see Channel Level on page 108 ).
No sound from one speaker.
Check the speaker connection (see Connecting the speakers on page 24 ).
Check the speaker level settings (see Channel Level on page 108 ).
Check that the speaker hasn’t been set to NO (see Speaker Setting on page 107 ).
The channel may not be recorded in the source. By using one of the advanced effect
listening modes, you may be able to create the missing channel (see Enjoying various
types of playback using the listening modes on page 71 ).
No digital sound is output.
Make sure that the digital input is assigned correctly for the input jack the component is
connected to (see The Input Setup menu on page 59 ).
Check the digital output settings on the source component.
Other audio problems
Symptom Remedy
Broadcast stations cannot be
selected automatically, or there is
considerable noise in radio broad-
casts.
Fully extend the FM wire antenna, adjust the position for best reception and secure to a
wall, etc.
Use an outdoor antenna for better reception (see pages 32 , 46 ).
Adjust the position and direction of the AM antenna.
Noise may be caused by interference from other equipment, such as a fluorescent light,
motor, etc. Switch off or move the other equipment, or move the AM antenna.
Subwoofer output is very low.
To route more signal to the subwoofer, set it to PLUS or set the front speakers to SMALL
(see Speaker Setting on page 107 ).
Everything seems to be set up cor-
rectly, but the playback sound is odd.
The speakers may be out of phase. Check that the positive/negative speaker terminals on
the receiver are matched with the corresponding terminals on the speakers (see Con-
necting the speakers on page 24 ).
The Phase Control feature doesn’t
seem to have an audible effect.
If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass
cutoff is set to the highest frequency setting. If there is a PHASE setting on your sub-
woofer, set it to 0º (or depending on the subwoofer, the setting where you think it has the
best overall effect on the sound).
Make sure the speaker distance setting is correct for all speakers (see Speaker Distance
on page 108 ).
Can’t select some Input functions
by the INPUT SELECTOR on the
front panel or the ALL button on the
remote control.
Check the Input Skip settings in the Input Setup menu (see The Input Setup menu on
page 59 ).
Check the HDMI Input assignment in the Input Setup menu then try OFF (see The Input
Setup menu on page 59 ).
There seems to be a time lag
between the speakers and the output
of the subwoofer.
See Automatically conducting optimum sound tuning (Full Auto MCACC) on page 58
to set up your system again using MCACC (this will automatically compensate for a delay
in the subwoofer output).
The maximum volume available
(shown in the front panel display) is
lower than the +12dB maximum.
Check that the Volume Limit is set to OFF (see Volume Setup on page 109 ).
The channel level setting may be over 0.0dB.
Certain listening modes or
HOME MENU items cannot be
selected.
Some functions cannot be selected, depending on the input signal and listening mode.
The volume level drops automati-
cally.
The temperature within the unit has exceeded the allowable value. Try moving the unit for
better ventilation (see Installing the receiver on page 11 ).
Volume seems different when input
is switched.
Set the Channel Level setting to ALL, then adjust the volume of the respective input
sources (see Input Volume Absorber on page 89 ).
VSX-1130 only: When HDZONE is ON,
multi-channel audio sources are not
output in the main zone.
When HDZONE is selected in Speaker System and also the same HDMI input is selected
for both the main zone and HDZONE, 2-channel PCM audio sources are output from the
main zone as well. To output multi-channel audio sources, set HDZONE to OFF or change
the HDZONE input.
VSX-1130 only: No HDZONE sound
is output.
With HDZONE, multi-channel audio may not be output. In this case, set the audio output
setting of your playback device to 2-channel PCM.
　
… 115 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

pioneer-vsx-830-k

Suche zurücksetzen

  • Hallo, ich möchte einen Plattenspieler (Grundig PS35) an den Verstärker anschließen und dann via PC die Schallplatten digitalisieren (Aufnahme über Soundkarte).
    Kann mir jemand erklären wie bzw. wo ich den Plattenspieler anschließen muss, damit ich die Musik durch den Verstärker hören bzw. an den PC weiterleiten kann?
    Plattenspieler hat keinen Entzerrvorverstärker. Eingereicht am 7-8-2023 12:19

    Antworten Frage melden

  • Die Lautstärke wird von Zeit zu zeit automatisch leiser! Wie kann ich das ändern? Eingereicht am 7-1-2018 19:20

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Pioneer VSX-830 K wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Pioneer VSX-830 K

Pioneer VSX-830 K Bedienungsanleitung - Deutsch - 146 seiten

Pioneer VSX-830 K Bedienungsanleitung - Holländisch - 146 seiten

Pioneer VSX-830 K Bedienungsanleitung - Französisch - 145 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info