574198
63
Zoom out
Zoom in
Vorherige Seite
1/88
Nächste Seite
Using other functions
10
63
En
Chapter 10:
Using other functions
Setting the AV options
There are a number of additional sound and picture
settings you can make using the AV Parameter menu.
The defaults, if not stated, are listed in bold.
Important
Note that if a setting doesn’t appear in the AV
Parameter menu, it is unavailable due to the current
source, settings and status of the receiver.
1 Press
RECEIVER
then press
AV PARAMETER
.
2 Use
/
to select the setting you want to adjust.
Depending on the current status / mode of the receiver,
certain options may not be able to be selected. Check the
table below for notes on this.
3 Use
/
to set it as necessary.
See the table below for the options available for each
setting.
4 Press
RETURN
to confirm and exit the menu.
Setting What it does Option(s)
C. WIDTH
a
(Center
Width)
(Applicable
only when
using a center
speaker)
Provides a better blend of the front
speakers by spreading the center
channel between the front right and
left speakers, making it sound wider
(higher settings) or narrower (lower
settings).
0 to 7
Default:
3
DIMEN-
SION
a
Adjusts the depth of the surround
sound balance from front to back,
making the sound more distant
(minus settings), or more forward
(positive settings).
–3 to +3
Default:
0
PANORA-
MA
a
Extends the front stereo image to
include the surround speakers for a
‘wraparound’ effect.
OFF
ON
C. IMAGE
b
(Center
Image)
(Applicable
only when
using a center
speaker)
Adjusts the center image to create a
wider stereo effect with vocals.
Adjust the effect from
0
(all center
channel sent to front right and left
speakers) to
10
(center channel sent
to the center speaker only).
0 to 10
Default:
3
EFFECT
Sets the effect level for the currently
selected Advanced Surround mode
(each mode can be set separately).
10 to 90
HI-BIT / HI-
SAMP
(High Bit /
High
Sampling)
Creates a wider dynamic range with
digital sources like CDs or DVDs.
OFF
ON
DNR
(Digital Noise
Reduction)
May improve the quality of sound in a
noisy source (for example, cassette
or video tape with lots of background
noise) when switched on.
OFF
ON
DUAL
(Dual Mono)
Specifies how dual mono encoded
Dolby Digital soundtracks should be
played. Dual mono is not widely used,
but is sometimes necessary when
two languages need to be sent to
separate channels.
CH1
– Chan-
nel 1 is heard
only
CH2
– Channel
2 is heard only
CH1 CH2
Both channels
heard from
front speakers
DRC
(Dynamic
Range
Control)
Adjusts the level of dynamic range for
movie soundtracks optimized for
Dolby Digital, DTS, Dolby Digital
Plus, Dolby TrueHD, DTS-HD and
DTS-HD Master Audio (you may need
to use this feature when listening to
surround sound at low volumes).
AUTO
c
OFF
MAX
MID
SACD
GAIN
d
Brings out detail in SACDs by
maximizing the dynamic range
(during digital processing).
0 to 6 (dB)
Default:
0
(dB)
DELAY
(Sound Delay)
Some monitors have a slight delay
when showing video, so the
soundtrack will be slightly out of sync
with the picture. By adding a bit of
delay, you can adjust the sound to
match the presentation of the video.
0.0 to 6.0
(frames)
1 second = 30
frames (NTSC)
LFE
(LFE
Attenuate)
Some Dolby Digital and DTS audio
sources include ultra-low bass tones.
Set the LFE attenuator as necessary
to prevent the ultra-low bass tones
from distorting the sound from the
speakers.
The LFE is not limited when set to
0 dB, which is the recommended
value. When set to –5 dB, –10 dB,
–15 dB or –20 dB, the LFE is limited by
the respective degree. When OFF is
selected, no sound is output from the
LFE channel.
0dB
–5dB/ –10dB/
–15dB/ –20dB/
OFF
HDMI
Specifies the routing of the HDMI
audio signal out of this receiver (
amp
)
or
through
to a TV or plasma display.
AMP
THROUGH
V. CONV
(Digital Video
Conversion)
Converts analog video signals for
output from the
MONITOR OUT
jacks for all video types.
ON
OFF
Setting
What it does Option(s)
VSX-9120TXH_KU.book 63 ページ 2007年4月12日 木曜日 午前11時47分
63

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Pioneer VSX-9120TXH-k wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Pioneer VSX-9120TXH-k

Pioneer VSX-9120TXH-k Bedienungsanleitung - Englisch - 30 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info