Bedienungsanleitung Pioneer VSX-9130TXH-k (Seite 11 von 104) (Englisch)

574199

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

5 minute guide

• With error messages (such as Too much ambient

noise! or Check Microphone.) select RETRY after

checking for ambient noise (see Problems when

using the Auto MCACC Setup below) and verifying the

mic connection. If there doesn’t seem to be a

problem, you can simply select GO NEXT and

continue.

The configuration shown on-screen should reflect the

actual speakers you have.

If you see an error message (ERR) in the right side

column (or the speaker configuration displayed isn’t

correct), there may be a problem with the speaker

connection. If selecting RETRY doesn’t work, turn off the

power and check the speaker connections. If there

doesn’t seem to be a problem, you can simply use /

to select the speaker and / to change the setting

(and number for surround back) and continue.

6 Make sure ‘

’ is selected, then press

ENTER

A progress report is displayed on-screen while the

receiver outputs more test tones to determine the

optimum receiver settings for Channel Level, Speaker

Distance, Standing Wave and Acoustic Cal EQ.

Again, try to be as quiet as possible while this is

happening. It may take 3 to 7 minutes.

7 The Auto MCACC Setup has finished! Press

RETURN

to go back to the System Setup menu.

Be sure to disconnect the microphone from this receiver

upon completion of the Auto MCACC setup.

The settings made in the Auto MCACC Setup should give

you excellent surround sound from your system, but it is

also possible to adjust these settings manually using the

System Setup menu (starting on page 38).

Problems when using the Auto MCACC Setup

If the room environment is not optimal for the Auto

MCACC Setup (too much background noise, echo off the

walls, obstacles blocking the speakers from the

microphone) the final settings may be incorrect. Check

for household appliances (air conditioner, fridge, fan,

etc.), that may be affecting the environment and switch

them off if necessary. If there are any instructions

showing in the front panel display, please follow them.

• Some older TVs may interfere with the operation of

the microphone. If this seems to be happening,

switch off the TV when doing the Auto MCACC Setup.

Playing a source

Here are the basic instructions for playing a source (such

as a DVD disc) with your home theater system.

1 Switch on your system components and receiver.

Start by switching on the playback component (for

example a DVD player), your TV

and subwoofer (if you

have one), then the receiver (press  RECEIVER).

• Make sure the setup mic is disconnected.

2 Select the input source you want to play.

You can use the input source buttons on the remote

control, INPUT SELECT, or the front panel controls.

3Press

AUTO/DIRECT

(

AUTO SURR

STREAM

DIRECT

) to select ‘

AUTO SURROUND

’ and start

playback of the source.

If you’re playing a Dolby Digital or DTS surround sound

DVD disc, you should hear surround sound. If you are

playing a stereo source, you will only hear sound from the

front left/right speakers in the default listening mode.

Note

1 If you’re using the front panel display, the diagram in Listening to Surround Sound on page 9 indicates (in bold) how each speaker is displayed.

2 You can also choose to view the settings from the MCACC Data Check screen. See Automatic MCACC (Expert) on page 38 for more on this.

3 • Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12 cm (5 inches) will end up with different size

settings. You can correct the setting manually using the Manual speaker setup on page 48.

• The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be accurate (taking delay and

room characteristics into account) and generally does not need to be changed.

• If Auto MCACC Setup measurement results are incorrect due to the interaction of the speakers and viewing environment, we recommend adjusting

the settings manually.

1.Auto MCACC

Now Analyzing

…

(2/9)

Environment Check

Ambient Noise [ OK ]

Microphone [ ]

Speaker YES/NO [ ]

:Cancel

1.Auto MCACC

CHECK!

Front [ YES ]

Center [ YES ]

Surr [ YES ]

SB [ YES x 2 ]

SW [ YES ]

:Cancel

4 Make sure that the TV’s video input is set to this receiver (for example, if you connected this receiver to the VIDEO 1 jacks on your TV, make sure that the

VIDEO 1 input is now selected).

5 If you need to manually switch the input signal type press SIGNAL SEL (page 33).

6 • You may need to check the digital audio output settings on your DVD player or digital satellite receiver. It should be set to output Dolby Digital, DTS and

88.2 kHz / 96 kHz PCM (2 channel) audio, and if there is an MPEG audio option, set this to convert the MPEG audio to PCM.

• Depending on your DVD player or source discs, you may only get digital 2 channel stereo and analog sound. In this case, the receiver must be set to a

multichannel listening mode (see Listening in surround sound on page 30 if you need to do this) if you want multichannel surround sound.

DVD BD TV HDMI

DVR 1 DVR 2 CD

XM SIRIUS

CD-R

DIMMER

FM/AM

123

SLEEPMCACC

INPUT

SELECT

GENRE

456

iPod USB

RECEIVER

SOURCE

DVD BD TV HDMI

DVR 1 DVR 2 CD

XM SIRIUS

CD-R

FM/AM

INPUT

SELECT

iPod USB

RECEIVER

INPUT

MUTE

EXIT TOOLS

AUDIO

PARAMETER

VOLCH

TV CONTROL

456

A.ATTSBchSR+

789

CLASS

MASTER

VOLUME

CH LEVELD.ACCESS

ENTER

TUNE

VIDEO

PARAMETER

MASTER

VOLUME

RETURN

iPod CTRL

SETUP

Pioneer VSX-9130TXH-k Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info