Bedienungsanleitung Pioneer VSX-9140TXH (Seite 60 von 123) (Englisch)

574068

Zoom out

Zoom in

Vorherige Seite

1/123

Nächste Seite

Listening to your system

Using the Virtual Surround Back mode

•Default setting: OFF

When you’re not using surround back speakers,

selecting this mode allows you to hear a virtual surround

back channel through your surround speakers. You can

choose to listen to sources with no surround back

channel information, or if the material sounds better in

the format (for example, 5.1) for which it was originally

encoded, you can have the receiver only apply this effect

to 6.1 encoded sources like Dolby Digital EX or DTS-ES.

• Press

SBch

repeatedly to cycle the virtual surround

back channel options.

Each press cycles through the options as follows:

• VirtualSB ON – Virtual Surround Back is always used

(for example, on 5.1 encoded material)

• VirtualSB AUTO – Virtual Surround Back is

automatically applied to 6.1 encoded sources (for

example, Dolby Digital EX or DTS-ES)

• VirtualSB OFF – Virtual Surround Back mode is

switched off

Setting the Up Mix function

In a 7.1-channel surround system with surround

speakers placed directly at the sides of the listening

position, the surround sound of 5.1-channel sources is

heard from the side. The Up Mix function mixes the

sound of the surround speakers with the surround back

speakers so that the surround sound is heard from

diagonally to the rear as it should be.

•Using the Up Mix function is effective when the

speakers in the 7.1-channel surround system are set

up as recommended in the example on page 18.

•Depending on the positions of the speakers and the

sound source, in some cases it may not be possible

to achieve good results. In this case, set the setting to

OFF.

1 Switch the receiver into standby.

2 While holding down

ENTER

on the front panel,

press

 STANDBY/ON

The display shows RESET  NO .

Use TUNE +/– (or / on the remote control) to select

UP MIX  ON , and then use PRESET +/– (or / on

the remote control) to select ON or OFF.

3 Press

ENTER

to confirm.

• When set to ON, the UP MIX indicator on the front

panel lights.

Note

1 • You can’t use the Virtual Surr ound Back mode when the headphones are connected to this receiver or when any of the stereo, Front Stage

Surround Advance or Stream Direct mode is selected.

•

You can only use the Virtual Surround Back mode if the surround speakers are on and the

setting is set to

or if

Front Bi-Amp

Speaker B

or ZONE 2 is selected at Surr Back System.

• The Virtual Surround Back mode cannot be applied to sources that do not have surround channel information.

2 • Set to ON regardless of this setting when playing DTS-HD signals.

• May automatically be set to OFF even when set to ON, depending on the input signal and listening mode.

L R

SL SR

SBL SBR SBL SBR

L R

SL SR

Up Mix OFF Up Mix ON

INPUT

SELECTOR

STANDBY/ON

PHONES

BAND

TUNE

PHASE

CONTROL

AUTO SURR

/ALC/

STREAM DIRECT

STEREO

ADVANC

MCACC

SPEAKERS CONTROL

MULTI-ZONE

OFF

HDMIPQLS

PRESET

TUNER EDIT

ENTER

PUSH

OPEN

VSX-9140TXH

VSX-9140TXH_CUXJ.book 60 ページ２００９年４月１６日　木曜日　午前１０時３６分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-9140TXH Seite 60

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info