Bedienungsanleitung Pioneer VSX-9140TXH (Seite 73 von 123) (Englisch)

574068

Zoom out

Zoom in

Vorherige Seite

1/123

Nächste Seite

Controlling the rest of your system

Chapter 9:

Controlling the rest of your system

Operating multiple receivers

The remote control included with this receiver can be

used to operate up to three other receivers (of the same

model as this receiver) in addition to this receiver. The

receiver to be operated is switched by inputting the

preset code to set the remote control setting.

•Set the remote modes on the receivers before using

this function (see Remote Control Mode Setup on

page 96).

1 Check the operation selector switch to

MAIN

2Press .

3 Press and hold

REMOTE SETUP

, then release it after

the LED flashes twice.

4 Use the number buttons to enter the 5-digit preset

code (see below).

• Receiver 1: 6 1 9 3 5 (Default)

• Receiver 2: 6 2 6 3 0

• Receiver 3: 6 2 6 3 1

• Receiver 4: 6 2 6 3 2

The LED flashes twice when the preset code has been

properly registered. When the preset code is fully input,

the LED flashes once to indicate that the setting has

failed.

To operate another receiver, start over from step 1 to

input its preset code.

Setting the remote to control other

components

Most components can be assigned to one of the input

function buttons (such as DVD or CD) using the

component’s manufacturer preset code stored in the

remote.

However, there are cases where only certain functions

may be controllable after assigning the proper preset

code, or the codes for the manufacturer in the remote

control will not work for the model that you are using.

Note

•You can cancel or exit any of the steps by pressing

. To go back a step, press RETURN.

•After one minute of inactivity, the remote

automatically exits the operation.

Selecting preset codes directly

1 Press the input function button for the component

you want to control.

When assigning preset codes to TV CONTROL, press TV

CTRL here.

2 Press and hold

REMOTE SETUP

, then release it after

the LED flashes twice.

3 Use the number buttons to enter the 5-digit preset

code.

See Preset code list on page 113.

The LED flashes twice when the preset code has been

properly registered. When the preset code is fully input,

the LED flashes once to indicate that the setting has

failed.

4 Repeat steps 1 through 3 for the other components

you want to control.

To try out the remote control, switch the component on or

off (into standby) by pressing  SOURCE. If it doesn’t

seem to work, select the next code from the list (if there

is one).

•Depending on the preset code, the signal may not be

transmitted when  SOURCE is pressed. In this case,

try operating other buttons to see if the remote

control is working.

123

SLEEP

HDMI OUT

MCACCSIGNAL SEL

456

DIMMERA.ATTSBch

789

CLASSCH LEVELD.ACCESS

ENTER

INPUT

SELECT

REMOTE

SETUP

ZONE 2

MAIN

ZONE 3

AUDIO

INFO

DISP

RECEIVER

TV CTRL

RECEIVER

Note

1 You can’t assign , TUNER, iPod/USB, XM or SIRIUS.

RECEIVER

VSX-9140TXH_CUXJ.book 73 ページ２００９年４月１６日　木曜日　午前１０時３６分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-9140TXH Seite 73

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info