Bedienungsanleitung Pioneer VSX-9140TXH (Seite 92 von 123) (Englisch)

574068

Zoom out

Zoom in

Vorherige Seite

1/123

Nächste Seite

The system and the other setup

• SB – Select the number of surround back speakers

you have (one, two or none).

Select LARGEx2 or

LARGEx1 if your surround back speakers reproduce

bass frequencies effectively. Select SMALLx2 or

SMALLx1 to send bass frequencies to the other

speakers or subwoofer. If you didn’t connect

surround back speakers choose NO.

• SW – LFE signals and bass frequencies of channels

set to SMALL are output from the subwoofer when

YES is selected. Choose the PLUS setting if you want

the subwoofer to output bass sound continuously or

you want deeper bass (the bass frequencies that

would normally come out the front and center

speakers are also routed to the subwoofer).

If you did

not connect a subwoofer choose NO (the bass

frequencies are output from other speakers).

3 Select ‘

X.OVER

’ and set the crossover frequency.

Frequencies below this point will be sent to the

subwoofer (or LARGE speakers).

4 When you’re finished, press

RETURN

You will return to the Manual SP Setup menu.

Channel Level

Using the channel level settings, you can adjust the

overall balance of your speaker system, an important

factor when setting up a home theater system.

1 Select ‘

Channel Level

’ from the

Manual SP Setup

menu.

2 Select a setup option.

• MANUAL – Move the test tone manually from

speaker to speaker and adjust individual channel

levels.

• AUTO – Adjust channel levels as the test tone moves

from speaker to speaker automatically.

3 Confirm your selected setup option.

The test tones will start after you press ENTER.

4 Adjust the level of each channel using

/

If you selected MANUAL, use / to switch speakers.

The AUTO setup will output test tones in the order shown

on-screen:

Adjust the level of each speaker as the test tone is

emitted.

5 When you’re finished, press

RETURN

You will return to the Manual SP Setup menu.

Tip

• You can change the channel levels by press

, then press CH LEVEL, and then using /

 on the remote control.

Note

1 • If you selected Speaker B, ZONE 2 or Front Bi-Amp (in Surround back speaker setting on page 91) you can’t adjust the surround back

settings.

• If the surround speakers are set to NO, the surround back speakers will automatically be set to NO.

• If you select one surround back speaker only, make sure that speaker is hooked up to the left surround back terminal.

2 If you have a subwoofer and like lots of bass, it may seem logical to select LARGE for your front speakers and PLUS for the subwoofer. This

may not, however, yield the best bass results. Depending on the speaker placement of your room you may actually experience a decrease in

the amount of bass due low frequency cancellations. In this case, try ch

anging the position or dire

ction of speakers. If you can’t get good

results, listen to the bass response with it set to PLUS and YES or the front speakers set to LARGE and SMALL alternatively and let your ears

judge which sounds best. If you’r e having problems, the easiest option is to route all the bass sounds to the subwoofer by selecting SMALL

for the front speakers.

3 • This setting decides the cutoff between bass sounds playing back from the speakers selected as LARGE, or the subwoofer, and bass sounds

playing back from those selected as SMALL. It also decides where the cutoff will be for bass sounds in the LFE channel.

• If you’re using a THX speaker setup, confirm that the crossover frequenc

y is set to 80Hz.

4a.Manual SP Setup

A/V RECEIVER

Exit Return

1. Surr Back System

2. Speaker Setting

3. Channel Level

4. Speaker Distance

5. X-Curve

6. THX Audio Setting

MCACC : M1.MEMORY 1

Test Tone : AUTO

4a3.Channel Level

A/V RECEIVER

Exit Return

4 • If you are using a Sound Pressure Level (SPL) meter, take the readings from your main listening position and adjust the level of each speaker

to 75 dB SPL (C-weighting/slow reading).

• The subwoofer test tone is output at low volumes. You may need to adjust the level after testing with an actual soundtrack.

5 The channel level cannot be adjusted using this procedure while making settings on HOME MENU.

CAUTION

Loud test tones will be output.

Please wait...**

4a3.Channel Level

A/V RECEIVER

Exit Cancel

A/V RECEIVER

Exit Finish

MCACC : M1.MEMORY 1

L : 0.0 dB

4a3.Channel Level

C : 0.0 dB

R : 0.0 dB

SBR : 0.0 dB

SR : 0.0 dB

SBL : 0.0 dB

SL : 0.0 dB

SW : 0.0 dB

RECEIVER

VSX-9140TXH_CUXJ.book 92 ページ２００９年４月１６日　木曜日　午前１０時３６分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-9140TXH Seite 92

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info