Bedienungsanleitung Pioneer VSX-920-K (Seite 88 von 400) (Englisch, Französisch)

574201

Zoom out

Zoom in

Vorherige Seite

1/400

Nächste Seite

The Advanced MCACC menu10

After a single calibration is performed, each of

the following three correction curves can be

stored separately in the MCACC memory.

SYMMETRY implements symmetric

correction for each pair of left and right

speakers to flatten the frequency-amplitude

characteristics. ALL CH ADJ is a ‘flat’ setting

where all the speakers are set individually so

no special weighting is given to any one

channel. FRONT ALIGN

sets all speakers in

accordance with the front speaker settings (no

equalization is applied to the front left and right

channels).

• THX Speaker (only available when the

Auto MCACC Menu above is ALL or

Speaker Setting) – Select YES if you are

using THX speakers (set all speakers to

SMALL), otherwise leave it set to NO.

•

STAND.WAVE Multi-P

(only available when

the

Auto MCACC

Menu above is

EQ Pro &

S-Wave

)

– In addition to measurements at

the listening position, you can use two more

reference points for which test tones will be

analyzed for standing waves. This is useful if

you want to get a balanced ‘flat’ calibration

for several seating positions in your

listening area.

Place the microphone at the

reference point indicated on-screen and

note that

the last microphone placement will

be at your main listening position:

3 Connect the microphone to the

MCACC

SETUP MIC

jack on the front panel.

Make sure there are no obstacles between the

speakers and the microphone.

If you have a tripod, use it to place the

microphone so that it’s about ear level at your

normal listening position. If you do not have a

tripod, use some other object to install the

microphone.

4 When you’re finished setting the options,

select

START

then press

ENTER

5 Follow the instructions on-screen.

• Make sure the microphone is connected.

• If you’re using a subwoofer, it is

automatically detected every time you

switch on the system. Make sure it is on

and the volume is turned up.

• See Problems when using the Auto MCACC

Setup on page 42 for notes regarding high

background noise levels and other possible

interference.

Note

1 If you selected ALL or Keep SP System as your Auto MCACC menu, you can specify the MCACC preset where you

want to save the SYMMETRY, ALL CH ADJ and FRONT ALIGN settings.

2Switch the Multi-P setting NO if you only use one listening position.

1 2

2nd reference

point

3rd reference

point

Main listening

position

3 Install the microphone on a stable floor. Placing the microphone on any of the following surfaces may make accurate

measurement impossible:

• Sofas or other soft surfaces.

• High places such as tabletops and sofa tops.

MASTER

VOLUME

MCACC

SETUP MIC

VIDEO CAMERA

iPod

iPhone

USB HDMI 5

CONTROL ON

OFF

Microphone

Tripod

VSX-1020/VSX-1025

VSX-1020_SYXCN.book 88 ページ２０１０年３月１２日　金曜日　午前９時１０分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-920-K Seite 88

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-920-K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info