586463

Pioneer VSX-930 K-S Seite 116

116
Zoom out
Zoom in
Vorherige Seite
1/142
Nächste Seite
116
FAQ
14
BT AUDIO
Symptom Remedy
The Bluetooth wireless technology
device cannot be connected or oper-
ated. Sound from the Bluetooth wire-
less technology device is not emitted
or the sound is interrupted.
Check that no object that emits electromagnetic waves in the 2.4 GHz band (microwave
oven, wireless LAN device or Bluetooth wireless technology apparatus) is near the unit. If
such an object is near the unit, set the unit far from it. Or, stop using the object emitting
the electromagnetic waves.
Check that the Bluetooth wireless technology device is not too far from the unit and that
obstructions are not set between the Bluetooth wireless technology device and the unit.
Set the Bluetooth wireless technology device and the unit so that the distance between
them is less than about 10 m (33 ft.) and no obstructions exist between them.
The Bluetooth wireless technology device may not be set to the communication mode
supporting the Bluetooth wireless technology. Check the setting of the Bluetooth wireless
technology device.
Check that pairing is correct. The pairing setting was deleted from this unit or the Blue-
tooth wireless technology device. Reset the pairing.
Check that the profile is correct. Use a Bluetooth wireless technology device that sup-
ports A2DP profile and AVRCP profile.
Video
Symptom Remedy
No image is output when an input is
selected.
Check the video connections of the source component.
Make sure the input assignment is correct for components connected using component
video or HDMI cables (see The Input Setup menu on page 59 ).
Check the video output settings of the source component.
Check that the video input you selected on your TV is correct.
Excluding VSX-830: When the HDMI OUT 1/2 setting of the output parameter function is
set to OFF, set it to ON.
Excluding VSX-830: If HDZONE is set to on, video images connected using a video cable or
component cable are not output from the HDMI terminal. To output video images, turn
HDZONE off (page 89 ).
When content that is protected by the HDCP 2.2 protocol is output from a source player,
output of video is not possible on televisions and projectors that do not support HDCP
2.2. Please prepare a television or projector that supports HDCP 2.2. Also, this receiver’s
HDCP 2.2 compatible input terminals are BD, HDMI IN 1, and HDMI IN 2. When making
connections other than the said terminal(s), please use these terminals instead.
Noisy, intermittent, or distorted
picture.
Sometimes a video deck may output a noisy video signal (during scanning, for example),
or the video quality may just be poor (with some video game units, for example). The pic-
ture quality may also depend on the settings, etc. of your display device. Reconnect the
source and display device using the same type of connection (component or composite),
then start playback again.
Video parameters cannot be used. For audio only input (TUNER, CD, and TV), the video parameter function cannot be used.
Use for video or input with a GUI display.
Settings
Symptom Remedy
The Auto MCACC Setup continually
shows an error.
The ambient noise level may be too high. Keep the noise level in the room as low as pos-
sible (see also Problems when using the Auto MCACC Setup on page 58 ). If the noise
level cannot be kept low enough, you will have to set up the surround sound manually
(page 106 ).
When using only one surround back speaker, connect it to the SURROUND BACK L
(Single) terminals.
To use a 5.1-channel speaker set, use the surround speakers for the surround channel,
not the surround back channel.
Make sure there are no obstacles between the speakers and the microphone.
If Reverse Phase is displayed, try the following:
— The speaker’s wiring (+ and –) may be inverted. Check the speaker connections.
— Depending on the type of speakers and their installation conditions, Reverse Phase
may be displayed even if the speakers are properly connected. If this happens, select
GO NEXT and continue.
— If the speaker is not pointed to the microphone (listening position) or when using
speakers that affect the phase (dipole speakers, reflective speakers, etc.), it may not be
possible to properly identify the polarity.
After using the Auto MCACC Setup,
the speaker size setting is incorrect.
There may have been some low frequency noise in the room from an air-conditioner,
motor, etc. Switch off all other appliances in the room and use Auto MCACC Setup again.
Depending on a number of factors (bass reproduction capabilities of the speakers, room
size, speaker placement, etc.) this may occur in some cases. Change the speaker setting
manually in Speaker Setting on page 107 , and use the ALL (Keep SP System) option for
the Auto MCACC menu in Automatic MCACC (Expert) on page 99 if this is a recurring
problem.
Can’t adjust the Fine Speaker Dis-
tance setting properly.
Check that the speakers are all in phase (make sure the positive (+) and negative (–)
terminals are matched up properly).
The display shows KEY LOCK ON
when you try to make settings.
With the receiver in standby, press u STANDBY/ON for about 5 seconds while holding
down SPEAKERS to disable the key lock.
Most recent settings have been
erased.
The power cord was disconnected from the wall while adjusting this setting.
Settings are only stored if all the zones are turned off. Turn off all the zones before
unplugging the power cord.
The various system settings are not
stored.
Do not pull out the power cord while conducting the settings. (The settings will be stored
when both the main zone and sub zone turn off. Turn off all zones before pulling out the
power cord.)
Feels like there is no subwoofer EQ
effect.
The effect becomes less when the set frequency value of the crossover frequency is low.
When setting a high frequency value, the subwoofer EQ effect becomes stronger. How-
ever, setting a higher crossover frequency increases the share that the subwoofer bears
for low-frequency playback. For that reason, it is disadvantageous in terms of the phase
point of view. Set to your preference.
　
… 116 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

pioneer-vsx-930-k-s

Suche zurücksetzen

  • kann man einen casettendeck an diesem internetanlage an schließen Eingereicht am 12-4-2021 18:24

    Antworten Frage melden

  • wie kann ich das internet-Radio die Sender einstellen Eingereicht am 29-3-2021 19:10

    Antworten Frage melden

  • klangeinstellung , equalizer, balance, einmessen - ich bitte um Anleitungen Eingereicht am 8-5-2017 10:06

    Antworten Frage melden

  • bei stromausfall alle radiosender weg Eingereicht am 6-1-2017 14:14

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Pioneer VSX-930 K-S wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Pioneer VSX-930 K-S

Pioneer VSX-930 K-S Bedienungsanleitung - Deutsch - 146 seiten

Pioneer VSX-930 K-S Bedienungsanleitung - Holländisch - 146 seiten

Pioneer VSX-930 K-S Bedienungsanleitung - Französisch - 145 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info