Bedienungsanleitung Pioneer VSX-AX3-S (Seite 41 von 104) (Englisch)

455258

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

Setting Up for Surround Sound

SURROUND SETUP

Channel Level

The following steps show you how to balance the sound output level of your speakers. Proper speaker balance is

essential for obtaining high quality surround sound. If continuing from SPEAKER SETTING go to step 1. If starting

fresh, complete steps 1–2 on page 38.

1 CHANNEL LEVEL should be selected. If it

isn’t use the  buttons to select and

press ENTER.

2 There are two ways to set the CHANNEL

LEVEL: MANUAL or AUTO. Select a

setting mode with the  buttons and

press ENTER.

Test tones will be output.

WARNING: Be prepared! The test tones are output at a

high volume level.

MASTER VOLUME rotates to the reference position (0 dB) and

the display on the receiver flashes TEST TONE. After a few

seconds the test tone is output.

MANUAL: move the test tone manually and adjust the chan-

nel level.

AUTO: the test tone moves by itself and you adjust the levels.

3 Adjust the speaker level with the

instructions below for the method you

chose.

Adjust the channel level from –10 dB to +10 dB in 0.5 dB

increments.

The default setting is 0 dB.

In MANUAL (manual test tone) mode

To switch the test tone between each speaker use the 

buttons and push ENTER. Adjust the level of each speaker

using the  buttons and ENTER. When done go to step 4.

In AUTO (automatic test tone) mode

This mode switches the test tone between each speaker auto-

matically. The test tone output cycles through the speakers in

the following order:

Adjust the level of each speaker using the  buttons as the

test tone is emitted and wait for it to move to the next speaker.

When done go to step 5.

If you want to change a setting before proceeding you

need to complete the procedure and start over from step 1.

4 When you have the levels you want

press ENTER. EXIT should be selected (if

it isn’t select it with the  buttons).

5 Press ENTER.

Next, proceed to SPEAKER DISTANCE next page.

Speaker Distance

Left

Right

Left

Right

1-5

in AUTO setting

in MANUAL setting

Memo:

• If your subwoofer has a volume control,

set it to the middle position before doing

these operations.

• If you are using a Sound Pressure Level

(SPL) meter take the readings from your

main listening position and adjust the

level of each speaker to 75dB SPL (C-

weighting/slow reading).

• The volume of the subwoofer test tone

tends to sound lower than it actually is.

You may need to adjust the level after

testing your system with an actual

soundtrack.

• You can also set the channel level

manually at any time by pressing

RECEIVER then EFFECT/CH SEL on the

remote control. Use the (+/–) buttons

directly below the EFFECT/CH SEL button

to adjust the level.

00_VSX-AX3.book Page 41 Monday, May 19, 2003 1:05 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-AX3-S Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-AX3-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info