Bedienungsanleitung Pioneer VSX-AX5i-S (Seite 29 von 120) (Englisch)

574069

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

Using i.LINK Interface

PREPARATION

Memo:

• When properly connected, the i.LINK plug will snap

into the connector. If not connected properly the

receiver will not be able to recognize any connected

components.

• After connecting an i.LINK-equipped component to

the receiver, follow the instructions for both assigning

inputs on the receiver (see page 91) and output

settings on the component (see the manual that

came with the component).

• You can connect several i.LINK-equipped components

together in the same way. See Creating an i.LINK

Network below.

• There may be cases where the PQLS/ rate control

function and/or the i.LINK audio does not work

properly even when connected to an i.LINK-Audio-

compatible equipment.

• Do not connect/disconnect i.LINK cables or switch

on/off any components connected using i.LINK while

the receiver is on.

Creating an i.LINK Network

Using the i.LINK interface it is possible to chain up to 17 components together so that the digital audio and

control signals from each component is available to other components in the network. With the addition of an

i.LINK repeater, it’s possible to connect up to 63 components.

i.LINK connectors come in 4-pin and 6-pin configurations. This receiver uses a 4-pin connection, but the two

types can be mixed on a network.

This receiver is compatible with i.LINK Audio (also called “A & M Protocol”) components, such as DVD

players. It may not work properly if connected to i.LINK MPEG-II TS equipment (such as a digital satellite

tuner), i.LINK DV equipment (such as a DVD recorder or DV camcorder), or an i.LINK-equipped personal

computer. Check the operating instructions supplied with your other i.LINK components for capability

information.

Receivers need to be DTCP (Digital Transmission Content Protection) compliant to be able to play DVD-A,

DVD-Video, and SACD i.LINK audio. This receiver is DTCP compliant, so you can use them.

When setting up an i.LINK network, it’s important that the components form an open ended chain (fig. 1), or

a tree (fig. 2).

The system will not work if the connected components form a loop. If a loop is detected, the message LOOP

CONNECT shows in the display. Figs. 3 and 4 show connections that form a loop.

Another consideration when connecting i.LINK devices is the speed of the interface. At present there are

three speeds; S100 (slowest), S200 and S400 (fastest). This receiver uses the S400 type. Although you can use

components with different speeds together, we recommend connecting slower-speed components at the

edge of the network if possible (shown by the shaded boxes in figs. 1 and 2). This will keep the network free of

bottlenecks.

When used within an i.LINK network, this receiver must be on for the i.LINK connection to be maintained.

Other components in the network may or may not maintain the connection in standby (none will when the

power is completely off)—check the operating instructions supplied with individual components. Note that

the audio may be momentarily interrupted if a component in the i.LINK network is switched on/off, or its

i.LINK connection is switched on/off.

 i.LINK connectors

Use a 4-pin, S400 i.LINK cable, less than 3.5 m long,

to connect i.LINK-equipped components.

Be sure to insert the

i.LINK cable straight

into connector. When

properly aligned the

cable can be inserted

with little resistance.

Forcing the cable into

the connector will

damage the connector

pins.

VSX-AX5i.book Page 29 Friday, May 23, 2003 6:33 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-AX5i-S Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-AX5i-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info