Bedienungsanleitung Pioneer VSX-D409 (Seite 23 von 60) (Englisch)

574208

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Set up

Press SETUP and hold for three seconds to

select the preset mode.

The LED will blink twice.

To cancel the preset mode

Press SETUP.

Press the MULTI CONTROL button for the

component you want to control.

Each button can be set to control one of the following components

DVD

: DVD/LD player or DVD Recorder

: TV , Satellite tuner or Cable TV tuner

: CD player, CD-R, Tape deck or MD recorder

CD-R

: CD player, CD-R, Tape deck or MD recorder

VCR

: VCR or Digital Video Recorder

TVC

: TV , Satellite tuner or Cable TV tuner

TUN

: FM/ AM tuner

Use the number buttons to enter the 4 digit

setup code.

The LED will blink after each digit is input and will blink twice to

confirm a valid code has been input.

If the LED shows one long blink it means an invalid code has been

input. Check the preset code list and try again. If you are not able

to input a preset code you can refer to page 26 to teach the remote

control individual commands.

Repeat steps 1 through 3 to assign preset codes for as many

components as necessary.

Press SETUP to exit the preset mode.

The remote control returns to the previous operation mode.

It will also return to the previous mode after ten seconds of

inactivify.

• The RCV (Receiver) button cannot be preset.

• You can only input a code for the component type written

on each MULTI CONTROL button. See page 29 for

information on how to program a different type of

component than specified on the button.

• If you recall a preset code for the tuner (TUN MULTI

COTROL), you will not be able to control the built-in tuner

of this receiver using the remote. To reset the remote to

the built-in tuner, input the preset code 0080.

Setting Up the Remote Control

In addition to controlling the receiver, the supplied remote control can operate your other components (DVD,

MD, VCR, TV, LD, CD, etc.). If your component(s) are listed in the “Preset Code List”, simply recall the

corresponding preset code.

Recalling preset codes (VSX-D509S)

The following steps show you how to recall preset codes for each MULTI CONTROL button. Once the preset

code is assigned, pressing the button will automatically set the remote to operate the respective component.

• Refer to “Preset Code List” on pages 53 to 56 for the components and manufacturers

available.

• Refer to “Controlling the Rest of Your System” on pages 46 to 50 for detailed explanations

on how to operate your other components.

memo

1,4

Preparations

Î

SOURCE

ENTER

TV CONTROL

TV VOL

TVFUNC

ENTER

D.ACCESS BAND CLASS

CH SELECT CH LEVEL

AV PRE-PROGRAMMED AND LEARNING

REMOTE CONTROL UNIT

DSP TEST TONE

FL DIMMER

LOUDNESS FUNCTION SETUPMUTING

MPX DTV ON / OFF DTV MENU

ST ST

CHANNEL

MASTER VOLUME

DISC

MULTI CONTROL

DVD TV VCR CD-R

RCV CD TUN TVC

RECEIVER

7



¢

3



¡

MIDNIGHT

SIGNAL SELECT EFFECT

+10

5.1CH ATT

123

456

789

LED

()

memo

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-D409 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info