Bedienungsanleitung Pioneer VSX-D850S (Seite 35 von 52) (Englisch)

574222

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Controlling the Rest of Your System

Recalling Preset Codes

The following steps show you how to recall preset codes

for each MULTI CONTROL button. Once the preset

code is assigned, pressing the button will automatically

set the remote to operate the respective component.

MEMO:

• Refer to “Preset Code List” on pages 43 to 49 for the

components and manufacturers available.

• Refer to “Controlling the Rest of Your System” on

pages 35 to 49 for detailed explanations on how to

operate your other components.

1 Press SETUP and hold for three seconds to

select the Preset mode.

The LED lights steadily for two seconds. (VSX-

D850S only: The LCD display shows SETUP.)

To cancel the preset mode at any time

Press SETUP.

The remote control will also return to the previous

mode after thirty seconds of inactivity.

2 Press the MULTI CONTROL button for the

component you want to control.

Each button can be set to control one of the

following components

DVD DVD/LD player or DVD Recorder

TV TV, Satellite tuner or Cable TV tuner

VCR VCR or Digital Video Recorder

CD CD player

CD-R CD Recorder, Tape deck

or MD player

TVC TV or Cable TV tuner

TUN FM/ AM tuner

TVFUNC

VOLUME

MASTER VOLUME

TV CONTROL

AV PRE-PROGRAMMED AND LEARNING

REMOTE CONTROL UNIT

CHANNEL

ENTER

DISC

DTV INFO

MPX/RETURN

DTV ON/OFF DTV MENU

D.ACCESS GUIDE

TUNE

CLASS

ATT

BAND

/DTS DSP

TEST TONE

CH SELECT CH LEVEL FUNCTION

SIGNAL SELECT

1¡

EFFECT

DVD VCR CD-RTV

RCV

TUN

TVC

MIDNIGHT

LOUDNESS

MUTING

SETUP

FL DIMMER

MULTI CONTROL

5.1 / 7.1

RECEIVER

SOURCE

3 Use the number buttons to enter the 4 digit

setup code. (see pages 43-49 for Preset Code

List)

The LED will blink for half a second after each digit

is input and will show a long, two second blink to

confirm a valid code has been input. (VSX-D850S

only: The code appears in the LCD display as you

input it. The display shows OK if it’s a valid code.)

If the LED blinks three times it means an invalid code

has been input or an error has occurred. Check the

preset code list and try again. If you are not able to

input a preset code you can refer to page 38 to teach

the remote control individual commands.

The remote control returns to the previous operation

mode. It will also return to the previous mode after

thirty seconds of inactivity.

4 Repeat steps 1 through 3 to assign preset

codes for as many components as necessary.

MEMO:

• You can only input a code for the component type

written on each MULTI CONTROL button.

• If you recall a preset code for the tuner (TUN MULTI

CONTROL), you will not be able to control the built-

in tuner of this receiver using the remote. To reset the

remote to the built-in tuner, input the preset code

7008.

• To erase the preset code for the current MULTI

CONTROL button, enter 0000 as the code in step 3.

LED

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-D850S Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info