Bedienungsanleitung Pioneer VSX-LX503 (Seite 139 von 1221) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch)

699659

139

Zoom out

Zoom in

Vorherige Seite

1/1221

Nächste Seite

139 Front Panel≫ Rear Panel≫ Remote≫

Contents

≫ Connections

≫ Playback

≫ Setup

≫

Full Auto MCACC

Place the supplied speaker setup microphone in the listening position, measure

the test tones emitted by the speakers, then the unit automatically sets the

optimum volume level for each speaker, the crossover frequencies, and the

distance from the listening position. This also reduces the e󰀨ect of the standing

wave in accordance with the viewing environment and automatically adjusts the

equalizers for the speakers and enables correction of distortion caused by the

acoustic environment of the room.

• Calibration takes between 3 and 12 minutes to be completed. The speakers

emit the test tone at high volume during measurement, so be careful of your

surroundings. Keep the room as quiet as possible during measurement.

• If you have connected a subwoofer, check the power and volume of the

subwoofer. Set the subwoofer volume to more than halfway.

• If the power of this unit suddenly turns o󰀨, the wires in the speaker cables

may have touch the rear panel or other wires and tripped the protection circuit.

Twist the wires again properly and make sure they do not stick out of the

speaker terminals when connecting.

1. Place the supplied speaker setup microphone in the listening position, and

connect to the MCACC SETUP MIC jack on the main unit.

MCACC

SETUP MI

When putting the speaker setup microphone on a tripod, refer to the illustration

when putting it in place.

2. Select the connected speaker conguration.

Height1Speaker

Height2Speaker

The image on the screen changes as you choose the number of channels in

"Speaker Channels", so refer to it when performing the settings.

3. Test tones are emitted by the speakers, and rstly the unit detects the

speakers connected and the noise in the environment.

4. The measurement results in step 3 are displayed. If there is no problem in

the detection result of the speaker, select "Next" and press ENTER to output

the test tone again to automatically set the settings such as volume level,

crossover frequency, etc., to their optimum. (The test tone is automatically

output when 10 seconds has elapsed without any operation.)

• When an error message is displayed or when the connected speakers

cannot be detected, perform re-measurement by selecting "Retry" and

pressing ENTER.

• When it cannot be resolved by performing the re-measurement, conrm

if the speakers are connected correctly. If there is any problem with the

speaker connection, perform the connection after disconnecting the power

cord.

5. Once the measurement is completed, it is possible to perform the

measurement in 2 additional listening positions. To perform the measurement,

select "Next" and press ENTER, then follow the instructions. To not perform

the measurement, select "Finish (Calculate)" and press ENTER.

6. Disconnect the speaker setup microphone.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-LX503 Seite 139

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-LX503

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info