Bedienungsanleitung Pioneer VSX-LX504 (Seite 183 von 203) (Englisch)

699656

183

Zoom out

Zoom in

Vorherige Seite

1/203

Nächste Seite

183

Front Panel≫ Rear Panel≫ Remote≫

Contents

≫

Connections

≫

Playback

≫

Setup

≫

 1. Speaker Setup

1. Select the connected speaker conguration, and press ENTER.

Note that the image on the screen changes each time you select the number

of channels in "Speaker Channels".

Speaker Setup

7.1.2 ch

Height 1 Speaker

Height 2 Speaker

Speaker Impedance 6 ohms or above

Zone 2 Preout

Zone 2

Top Middle

2. The speaker combination selected in step 1 is displayed. "Yes" is displayed for

the selected speakers. If the setting is correct, press ENTER.

3. Select "Next" and press ENTER. Then a test tone is output from each speaker

to conrm the connection. Selecting each speaker with the cursors / will

output the test tone. Press ENTER after conrmation.

4. If there is no problem with the speaker connection, select "Next" and press

ENTER. To return to "Speaker Setup", select "Back to Speaker Setup" and

press ENTER.

 2. Full Auto MCACC

Place the supplied speaker setup microphone at the listening position. The unit

automatically measures the test tones output from each speaker, and sets the

optimum volume level for each speaker, the crossover frequencies, and the

distance from the listening position. This also reduces the eect of the standing

wave in accordance with the viewing environment and automatically adjusts the

equalizers for the speakers, and enables correction of sound distortion caused by

the acoustic environment of the room.

• It takes between 3 and 12 minutes for calibration to be completed. Each

speaker outputs the test tone at high volume during measurement, so be

careful of your surroundings. Also, keep the room as quiet as possible during

measurement.

• If you connect a subwoofer, check the power and volume of the subwoofer.

Set the subwoofer volume to more than half.

• If the power of this unit suddenly turns o, the wires in the speaker cables

have touched the rear panel or other wires, and the protection circuit is

working. Twist the wires again securely, and make sure they do not stick out of

the speaker terminals when connecting.

1. Place the supplied speaker setup microphone at the listening position, and

connect it to the SETUP MIC jack on the main unit.

SETUP MI

When placing the speaker setup microphone on a tripod, refer to the

illustration.

2. Conrm a test tone is output from the subwoofer and press ENTER.

3. Press ENTER. Then, test tones are output from each speaker, and the

connected speakers and the noise in the surrounding environment are

automatically measured.

4. The measurement results in step 3 are displayed. If there is no problem in

the detection result of the speaker, select "Next" and press ENTER to output

the test tone again to automatically set the settings such as volume level,

crossover frequency, etc., to their optimum. (The test tone is automatically

output when 10 seconds has elapsed without any operation.)

• When an error message is displayed or when the connected speakers

cannot be detected, perform re-measurement by selecting "Retry" and

pressing ENTER.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-LX504 Seite 183

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-LX504

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info