Bedienungsanleitung Pioneer VSX-S500-S (Seite 10 von 56) (Englisch)

491888

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Connecting your equipment

Some tips for improving sound quality

Important

• Speakers such as S-HV500-LR and S-HV600B may have

specific installation methods. For more details, refer to

the operating instructions supplied with speaker.

Where you put your speakers in the room has a big effect on

the quality of the sound. The following guidelines should help

you to get the best sound from your system.

• It is best to angle the speakers towards the listening

position. The angle depends on the size of the room. Use

less of an angle for bigger rooms.

• Refer to the chart below for placement of speakers you

intend to connect.

Place the surround speakers at 120º from the center. If

you, (1) use the surround back speaker, and, (2) don’t

use the front height speakers, we recommend placing

the surround speaker right beside you.

If you intend to connect only one surround back

speakers, place it directly behind you.

If the surround speakers cannot be set directly to the

side of the listening position with a 7.1-channel system,

the surround effect can be enhanced by turning off the

Up Mix function (see Setting the Up Mix function on

page 33).

• For the best stereo effect, place the front speakers 2 m to

3 m apart, at equal distance from the TV.

• If you’re using a center speaker, place the front speakers

at a wider angle. If not, place them at a narrower angle.

• Place the center speaker above or below the TV so that the

sound of the center channel is localized at the TV screen.

Also, make sure the center speaker does not cross the

line formed by the leading edge of the front left and right

speakers.

• Surround and surround back speakers should be

positioned 60 cm to 90 cm higher than your ears and

titled slight downward. Make sure the speakers don’t face

each other. For DVD-Audio, the speakers should be more

directly behind the listener than for home theater

playback.

• Try not to place the surround speakers farther away from

the listening position than the front and center speakers.

Doing so can weaken the surround sound effect.

• Place the left and right front height speakers at least one

meter directly above the left and right front speakers.

• If you’re going to place speakers around your CRT TV, use

shielded speakers or place the speakers at a sufficient

distance from your CRT TV.

• The subwoofer can be placed on the floor. Ideally, the

other speakers should be at about ear-level when you’re

listening to them. Putting the speakers on the floor

(except the subwoofer), or mounting them very high on a

wall is not recommended.

• When not connecting a subwoofer, connect speakers

with low frequency reproduction capabilities to the front

channel. (The subwoofer’s low frequency component is

played from the front speakers, so the speakers could be

damaged.)

• After connecting, be sure to conduct the Auto

MCACC (speaker environment setting) procedure.

See Automatically setting up for surround sound (MCACC)

on page 19.

CAUTION

• Make sure that all speakers are securely installed. This

not only improves sound quality, but also reduces the risk

of damage or injury resulting from speakers being

knocked over or falling in the event of external shocks

such as earthquakes.

Connecting the speakers

The receiver will work with just two stereo speakers (the front

speakers in the diagram) but using at least three speakers is

recommended, and a complete setup is best for surround

sound.

Make sure you connect the speaker on the right to the right

(R) terminal and the speaker on the left to the left (L) terminal.

Also make sure the positive and negative (+/–) terminals on

the receiver match those on the speakers.

You can use speakers with a normal impedance between 4 Ω

and 16 Ω.

Be sure to complete all connections before connecting this unit

to the AC power source.

CAUTION

• These speaker terminals carry HAZARDOUS LIVE

voltage. To prevent the risk of electric shock when

connecting or disconnecting the speaker cables,

disconnect the power cord before touching any

uninsulated parts.

• Make sure that all the bare speaker wire is twisted

together and inserted fully into the speaker terminal. If

any of the bare speaker wire touches the back panel it

may cause the power to cut off as a safety measure.

• Do not allow the speaker cable core to come into contact

with the receiver body.

If the speaker cable core comes into contact with any

metal portion of the receiver’s body, it may damage the

speakers and cause smoke and fire.

Insert speaker cables securely into the terminals and

check that the cable does not come out of easily.

FHL

SBL

SBR

FHR

30 30

120 120

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-S500-S Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-S500-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info