Bedienungsanleitung Pioneer VSX-S500-S (Seite 35 von 56) (Englisch)

491888

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Listening to your system

a. BASS settings cannot be adjusted when the front speaker is

set to SMALL in the Speaker Setting (or is set automatically via

the Auto MCACC setup) and the X.Over is set above 150 Hz. In

this case, adjusting the subwoofer channel levels via CH LEV

allows for similar adjustments to those that could otherwise

be performed via BASS (page 38).

b. • Channels are displayed as follows.

L – Front left

FHL – Front height left

C – Center

FHR – Front height right

R – Front right

SR – Surround right

SBR – Surround back right

SBL – Surround back left

SL – Surround left

SW – Subwoofer

• Speakers for which Speaker Settings are set to NO cannot

be selected.

c. With a 7.1-channel surround system, audio signals that have

undergone matrix decoding processing through surround

back channel processing to which the Up Mix function is

added are output from the surround back speakers.

d. • Phase matching is a very important factor in achieving

proper sound reproduction. If two waveforms are ‘in phase’,

they crest and trough together, resulting in increased

amplitude, clarity and presence of the sound signal. If a crest

of a wave meets a trough, then the sound will be ‘out of phase’

and an unreliable sound image will be produced.

• If your subwoofer has a phase control switch, set it to the

plus (+) sign (or 0°). However, the effect you can actually feel

when Phase Control is set to ON on this receiver depends on

the type of your subwoofer. Set your subwoofer to maximize

the effect. It is also recommended you try changing the

orientation or the place of your subwoofer.

• Set the built-in lowpass filter switch of your subwoofer to

OFF. If this cannot be done on your subwoofer, set the cutoff

frequency to a higher value.

• If the speaker distance is not properly set, you may not have

a maximized Phase Control effect.

• The Phase Control mode cannot be set to ON in the

following cases:

– When the PURE DIRECT mode is switched on.

– When the headphones are connected.

e. You can change the Sound Retriever feature at any time by

using S.RTRV button.

f. The default setting when the iPod USB, NETWORK or

ADAPTER input is selected is ON.

g. This setting works only with dual mono encoded Dolby Digital

and DTS soundtracks.

h. The initial set AUTO is only available for Dolby TrueHD signals.

Select MAX or MID for signals other than Dolby TrueHD.

i. You shouldn’t have any problems using this with most SACD

discs, but if the sound distorts, it is best to switch the gain

setting back to 0 dB.

j. This feature is only available when the connected display

supports the automatic audio/video synchronizing capability

(‘lip-sync’) for HDMI. If you find the automatically set delay

time unsuitable, set AUTO DELAY to OFF and adjust the delay

time manually. For more details about the lip-sync feature of

your display, contact the manufacturer directly.

k. Only available with 2-channel sources in 2PLII MUSIC mode.

l. Only when listening to 2-channel sources in NEO:6 CINEMA

and NEO:6 MUSIC mode.

CENTER WIDTH

(Applicable only when using a center speaker)

Spreads the center channel between the front

right and left speakers, making it sound wider

(higher settings) or narrower (lower settings).

0 to 7

Default: 3

DIMENSION

Adjusts the surround sound balance from

front to back, making the sound more distant

(minus settings), or more forward (positive

settings).

–3 to +3

Default: 0

PANORAMA

Extends the front stereo image to include

surround speakers for a ‘wraparound’ effect.

OFF

CENTER IMAGE

(Applicable only when using a center speaker)

Adjust the center image to create a wider

stereo effect with vocals. Adjust the effect

from 0 (all center channel sent to front right

and left speakers) to 10 (center channel sent

to the center speaker only).

0 to 10

Default: 3

(NEO:6 MUSIC),

10 (NEO:6

CINEMA)

HEIGHT GAIN

Adjusts the output from the front height

speaker when listening in 2PLIIz HEIGHT

mode. If set to HIGH, the sound from the top

will be more emphasized.

HIGH

MID

LOW

Setting/What it does Option(s)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-S500-S Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-S500-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info