Bedienungsanleitung Pioneer VSX-S500-S (Seite 46 von 56) (Englisch)

491888

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Additional information

HDMI

No picture or sound.

 If the problem still persists when connecting your HDMI

component directly to your monitor, please consult the

component or monitor manual or contact the manufacturer

for support.

No picture.

 Video signals that are input from the analog video terminal

will not output from the HDMI terminal. Signals that are input

from the HDMI terminal will not output from the analog video

terminal. Be consistent with the type of cable between input

and output.

 Depending in the output settings of the source component, it

may be outputting a video format that can’t be displayed.

Change the output settings of the source, or connect using

the composite video jacks.

 This receiver is HDCP-compatible. Check that the components

you are connecting are also HDCP-compatible. If they are not,

please connect them using the composite video jacks.

 Depending on the connected source component, it’s possible

that it will not work with this receiver (even if it is HDCP-

compatible). In this case, connect using the composite video

jacks between source and receiver.

 If video images do not appear on your TV, try adjusting the

resolution, Deep Color or other setting for your component.

 To output signals in Deep Color, use an HDMI cable (High

Speed HDMI

Cable) to connect this receiver to a component

or TV with the Deep Color feature.

The OSD screen (Home Menu, etc.) isn’t displayed.

 The OSD will not appear if you have connected using the

HDMI output to your TV. Use composite connections when

setting up the system.

No sound, or sound suddenly ceases.

 Check that the HDMI setting is set to AMP (refer to page 33).

 If the component is a DVI device, use a separate connection

for the audio.

 HDMI format digital audio transmissions require a longer time

to be recognized. Due to this, interruption in the audio may

occur when switching between audio formats or beginning

playback.

 Turning on/off the device connected to this unit’s HDMI OUT

terminal during playback, or disconnecting/connecting the

HDMI cable during playback, may cause noise or interrupted

audio.

Synchronized operation not possible using Control with

HDMI function.

 Check the HDMI connections.

 The cable may be damaged.

 Select ON for the Control with HDMI setting (see HDMI Setup

on page 41).

 Turn the TV’s power on before turning on this receiver’s power.

 Set the TV side Control with HDMI setting to on (see TV’s

operating instructions).

 When the Ecology mode is switched on, the Control with

HDMI function does not work.

 When the Ecology mode is turned off again, the Control with

HDMI function may not work. In this case, see Before using

synchronization on page 42.

Important information regarding the HDMI

connection

There are cases where you may not be able to route HDMI

signals through this receiver (this depends on the HDMI

equipped component you are connecting-check with the

manufacturer for HDMI compatibility information).

If you aren’t receiving HDMI signals properly through this

receiver (from your component), please try the following

configuration when connecting up.

Configuration

Connect your HDMI-equipped component directly to the

display using an HDMI cable. Then use the most convenient

connection (digital is recommended) for sending audio to the

receiver. See the operating instructions for more on audio

connections. Set the display volume to minimum when using

this configuration.

Note

• Depending on the component, audio output may be

limited to the number of channels available from the

connected display unit (for example audio output is

reduced to 2 channels for a monitor with stereo audio

limitations).

• If you want to switch the input source, you’ll have to

switch functions on both the receiver and your display

unit.

• Since the sound is muted on the display when using the

HDMI connection, you must adjust the volume on the

display every time you switch input sources.

About status messages

Refer to the following information when you come up with a

status message while operating the NETWORK function.

Status messages Descriptions

List empty, Add from

Now Playing...

The list is empty. Please add from Now

Playing.

No item There are no items.

Rescanning devices... Rescanning. Please wait.

Unsupported Format This format is not supported.

Server Connection

Error

Cannot connect to server.

Error opening stream This is a stream error.

Already in favorites This is already registered in your

favorites.

Unsupported item This item is not supported by this

receiver.

Unknown error An unidentified error has occurred.

Connection Error... Cannot connect to network.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-S500-S Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-S500-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info