Bedienungsanleitung Pioneer XN-P02 (Seite 22 von 54) (Englisch)

611811

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

Playback with NETWORK features (Network audio player: N-P01)

A: Wired setting

Make sure that the LAN cable connections has completed

(page 12

Press NET SERVICE



SETUP.

The Initial Setup screen is shown on the display.

Select Network Setting



Network Configuration.

Use

/

to select Wired, then press ENTER.

Use

/

to select DHCP On, then press ENTER.

Select Don’t Use Proxy Server.

Note

•

If your router does not have a built-in DHCP server function,

you have to set up the network manually.

 Select DHCP to be Off and press ENTER in step 4.

Then use /// or numeric buttons to adjust the

numbers, then press ENTER.

/: Moves the adjusting digit.

/: Increases or decreases values.

IP Address

The IP address to be entered must be defined within the

following ranges. If the IP address defined is beyond the

following ranges, you cannot play back audio files stored

on components on the network or listen to Internet radio

stations.

Class A: 10.0.0.1 to 10.255.255.254 / Class B: 172.16.0.1 to

172.31.255.254 / Class C: 192.168.0.1 to 192.168.255.254

Subnet Mask

If an xDSL modem or a terminal adapter is directly

connected to this player, enter the subnet mask listed in

your ISP documentation. In most of the cases, enter

255.255.255.0.

Default Gateway

If a gateway (router) is connected to this player, enter the

corresponding IP address.

Primary DNS Server/Secondary DNS Server

If there is only one DNS server address listed in your ISP

documentation, enter Primary DNS Server. In case there

are more than two DNS server addresses, enter

Secondary DNS Server in the other DNS server address

field.

•

When you connect this player to the Internet via a proxy

server, proxy server settings are required.

Select Use Proxy Server and press ENTER in step 4.

Then Enter Proxy Host Name and the port number of

your proxy server in the Proxy Port field.

B: Connection settings using an iOS device

(with iOS 5.0 or later)

You can apply iPod/iPhone/iPad (iOS device with iOS ver 5.0

or later)’s Wi-Fi settings to this player.

Note

•

The iOS device and router must be connected at 2.4 GHz.

Be sure the LAN cable is not connected to the player.

Unlock your iPod/iPhone/iPad. Check that the Wi-Fi

mark is displayed on the iOS device.

Plug the power cord into an AC outlet. Press STANDBY/

ON.

Press iPod/USB on the remote control.

Connect the iOS device to the USB terminal.

Press SETUP.

Select Network Setting



Network Configuration



Wireless



iOS Device and then press ENTER.

Tap Allow on iPod/iPhone/iPad.

The Wi-Fi settings of your iPod/iPhone/iPad are applied to

the player.

Wireless

Wired

Network Configuration

DHCP Off

DHCP On

Network Configuration



IP Address

XXX

XXX XXX XXX

Share Wi-Fi Settings?

Ignore

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer XN-P02 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer XN-P02

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info