Bedienungsanleitung Pioneer XN-P02 (Seite 34 von 54) (Englisch)

611811

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

Additional information (Network audio player: N-P01)

 A Spotify Premium account (for a charge) must be registered

on the Spotify application.

 When this unit is in standby, it cannot be selected from the

Spotify application.



The sound of the Spotify audio stream is not produced.

 Check whether this unit is selected on the Spotify application.

 Check that contents are playing on the Spotify application.

 If the above does not solve the problem, turn this unit’s power

off then back on.



This unit’s volume does not increase when the volume

slider in the Spotify application is raised.

 There is an upper limit to the volume to prevent the volume

from being too high accidentally. To raise the volume higher in

this case, do so by operating the remote control. When using

an application such as Pioneer ControlApp, the volume can

also be increased from the application.



Playback continues on this unit when the Spotify

application is quit.

 The Spotify audio stream continues from this unit, even when

the Spotify application is quit. To operate again, relaunch the

Spotify application.

Wireless LAN



Network cannot be accessed via wireless LAN.

 Is Network Type set to Auto and the LAN cable connected to

the player? Switch Network Type to Wireless or disconnect

the LAN cable from the player, then restart the player. If

Network Type is set to Auto and the LAN cable is connected

to the player, the player recognizes the Network Type as

Wired.

 This player and base receiver (wireless LAN router, etc.) are too

far apart or there is an obstacle between them. Improve the

wireless LAN environment by moving the player and base

receiver closer together, etc.

 There is a microwave oven or other device generating

electromagnetic waves near the wireless LAN environment.

Use the system in a place away from microwave ovens or

others device generating electromagnetic waves. Avoid using

devices generating electromagnetic waves as much as

possible when using the system with the wireless LAN.

 Multiple wireless devices are connected to the wireless LAN

router. When connecting multiple wireless devices, their IP

addresses must be changed.

 Wireless LAN connections cannot be established between the

player and base receiver (wireless LAN router, etc.). The player

must be set in order to establish wireless LAN connections.

See Connecting using wireless LAN on page 12.

 The IP address settings of the player does not match the

settings of the wireless LAN router, etc. Check the IP address

settings of the player (including the DHCP setting). If the

player’s DHCP setting is on, turn the player’s power off, then

turn the power back on. Check that the IP address of the player

matches the settings of the wireless LAN router, etc. If the

player’s DHCP setting is off, set an IP address matching the

network of the base receiver (wireless LAN router, etc.). For

example, if the wireless LAN router’s IP address is

“192.168.1.1”, set the player’s IP address to “192.168.1.XXX”

(*1), the subnet mask to “255.255.255.0”, the gateway and DNS

to “192.168.1.1”.

*1) Set the “XXX” in “192.168.1.XXX” to a number between 2

and 248 that is not assigned to other devices.

 The access point is set to conceal the SSID. In this case, the

SSID may not be displayed on the access point list screen. If

not, set the SSID, etc., by making the wireless LAN settings on

the player manually.

 The access point’s security settings use WEP 152-bit length

code key or shared key authentication. The player does not

support WEP 152-bit length code key or shared key

authentication.

 The SSID only supports use of single-byte alphanumeric

characters, together with the underbar and certain other

symbols. If using another character coding, the SSID must be

updated before making network settings. For more details

regarding SSID, consult your router’s operating instructions.

Setting quick start mode

Quick start mode significantly reduces the time required for

startup. It also allows the unit to power on automatically using

AirPlay, DLNA and Spotify application. Follow the steps below

to turn on quick start mode. Power consumption increases

when set to quick start mode when compared to regular

standby mode.

Press NET SERVICE, then press SETUP on the remote

control.

The Initial Setup screen is shown on the display.

Select ‘Option Setting’ from Initial Setup menu.

Select ‘Power Off Setting’ from Option Setting menu.

Select ‘Quick Start Mode’ from Power Off Setting menu.

To turn Quick Start Mode on, Use

/

to select ON,

then press ENTER.

To turn Quick Start Mode off, Use

/

to select OFF,

then press ENTER.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer XN-P02 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer XN-P02

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info