Bedienungsanleitung Plieger REV 800 - 0046800 (Seite 11 von 78) (Alle Sprachen)

638821

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

Installation

Home receiver unit:

Mains operation:

Battery operation:

Remote sensor for thermo-hygrometer

Plug in the mains adapter (21) into the adapter socket at the backside (20) for

basic operation and continuous backlight. Additionally insert 3 pieces of AA batteries to assure the

current supply during a power failure.

If a continuous backlight is not necessary you only have to insert 3 pieces of

AA batteries. The backlight can be activated for about 15 seconds by pushing the button

“Snooze/Light/Sound” (10).

After the installation of the device the unit of the pressure is flashing. Select between the pressure

units mb (millibar), inHg (inches of mercury) and hPA (hektopascal) with buttons 3 and 4 and

choose with button “Pressure” (7). Now the spot height is flashing, which can be selected in the

same manner. The more exact the spot height of the location, the more exact is also the weather

forecast.

Loosen the screws on the battery door with a small screwdriver

Insert 2 pieces of AAA batteries according to the indicated polarity

Channel 1 is preselected. If more than one sensor is used you have to select channel 2 and 3

for the 2nd and 3rd sensor.

To connect to the main station press and hold the “CHANNEL/SEARCH”-button (5) on main unit

until you hear a beep sound.

Press the “TX”-button (B) for the registration of the outdoor sensor on the main station, so that

the measured values will be shown on the main station after a successful transmission.

Select degree unit Celsius (C) or Fahrenheit (F) by pushing the “C/F”-button (A).

Close the battery compartment.

Press the bell push button (15). On the receiver, the signal tone sounds. Select the loudness by

using the volume control (17).

Automatic adjustment of time and date

Pushing the button “ ” results in a synchronisation with the radio clock in Mainflingen (Germany).

In this process the antenna symbol flashes until a successful transmission and afterwards it is

shown permanently. If a transmission is not possible, the process must be repeated on another

place.

The weather station should be synchronised apart from electrical devices, because they

have a negative influence on the synchronisation.

If a synchronisation is also not possible after several attempts, the time and date can also be

adjusted manually as described in the following. During the next synchronisation the manual

adjusted values will be overwritten.

Note:

Manual adjustment of time and date

By pushing the “Clock”-button (1) for 3 seconds the display “24H” starts flashing. Now the desired

settings can be selceted with buttons 3 and 4 and confirmed by pushing “Clock” (1) again.

The different settings are all adjusted in the same manner and have the following sequence:

24H/12H (format) hour minute year date (format) month day.

The weekday and moon phase indicator will be added automaticly according to the entered date.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Plieger REV 800 - 0046800 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info