Bedienungsanleitung Plugwise Home Basic (Seite 5 von 8) (Englisch)

561266

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Attention: When not all placed plugs appear in the list, this can be due to one of the following reasons:

Not all plugs have been signed on or recognized by the network: -

If multiple networks are active in the immediate surroundings, the process to sign on the plugs may take a

little longer. After approximately 5 minutes all plugs should appear on screen.

One or more plugs are unreachable: -

When a plug is placed too far from the others it cannot communicate with the network. To solve this you can

place the plug closer to the others or place another plug in between the unreachable plug and the others.

Please make sure that the distance between the plugs is no more than 5 meters.

The plug does not work: -

If both abovementioned steps do not lead to a complete picture of your network in the screen of ‘Select

Modules’, you may reset the plug. For a complete explanation of this procedure we refer you to the Detailed

Manual to be accessed by clicking on the Question-mark Icon on the lower right side of the program.

• The Wizard will guide you further through a number of screens to entering data in order to create a network.

Proceed with all the steps of the wizard and click on ‘complete’ . The system will be activated.

• Save the installation list with the Licence Code.

Use software

Your Energy Management System is now installed! By using the software you can now measure and switch your appliances.

You can save on your energy-consumption by sending switching schedules to the plugs. As a service you may ﬁnd hereunder

a software-window with instructions.

Technical information

The computer can be switched off whilst the system continues to operate. The plugs have their own memory so even when

the computer is not switched on the measured data are stored and the plugs will switch according to the switching schedules

you entered. As soon as the computer is switched on (with the Stick connected) the stored data are retrieved from the plugs

and the complete overview of the energy-consumption is realized.

In order for the software to communicate with the products the Stick should be kept connected to the computer. You may

disconnect the Stick however this leads to interrupted communication between the plugs and the computer which means

that the current usage is not displayed and new usage data are not claimed. The disconnection does not interrupt the

actions of the network or the data already stored in the software, like the switching schedules. As soon as the Stick in

connected to the computer again, the software program will have to be started again. The computer then retrieves all data

stored in the plugs and in case new switching schedules are entered, they will be activated.

Switching, program switching

schedules in order to save.

Overviews, look at reports and

graphs of the energy consumption,

the costs and the CO2-emission.

irect Switching, the

ted appliance or group

rectly switched on/off .

Usage data, preset the timeframe

for use. The graph is empty until

data have been received.

Settings, add plugs, create groups

and rooms.

ick, the Stick ﬂashes

en data are retrieved

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Plugwise Home Basic Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info