Bedienungsanleitung Polar PFL 1021-D (Seite 2 von 2) (Englisch)

632190

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

CONSUMPTION DATA

ADD DETERGENTS, CLOSE THE DOOR AND

SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

“DOOR OPEN” INDICATION

Before starting and after end of a programme, the lamp

lights to show the the door can be opened. As long

as a wash programme is running, the door remains

locked and must on no account be forced open.

In case you have an urgent need to open it during a

running programme, refer to “Cancel (Reset) a running

programme before the end”.

PROGRAMME START

Open the tap and press the “Start/Pause” button.

The indication lamp next to the “Start/Pause” button

lights up. The programme sequence indicator shows the

current programme phase, running from left to right

through Wash, Rinse, Spin/Drain.

PROGRAMME END

• All the lights of the programme sequence indicator

are off, and the “Door open” indication lights up.

1. Turn the programme selector to the “Off/O”

position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry.

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

1. Press the “Start/Pause” button to pause the

programme. The light blinks.

2. Select the new programme (with temperature), any

options and another spin speed if you want.

3. Press the “Start/Pause” button again. The new

programme continues at the same position where

the previous programme was interrupted. Do not

add detergent for this programme.

CANCEL (RESET) A RUNNING PROGRAMME

BEFORE THE END

START DELAY

Add detergents as indicated on the front page and as

described in the chapter “Detergent and Additives” in

your Instructions for Use.

• Turn the programme selector to the desired

programme and temperature.

• The display shows the programme duration and the

predefined spin speed.

• The indication lamp next to the “Start/Pause”

button blinks.

The “Reset” button cancels a programme before the

end.

• Press and hold the “Reset” button for a few seconds.

Any existing water is drained out. It may last

some time until the door can be opened.

The “Start delay” allows to run the machine at the

consumer’s convenience, for example at night when

electricity is cheaper. Do not use liquid detergent when

activating “Start delay” option.

• Select programme, temperature and options.

• Press the “Start delay” button to select the desired

delay time between 30 minutes and 23 hours.

• Press the “Start/Pause” button.

On the display, the start delay symbol and the dot

between hours and minutes blink. The countdown of

the delay time begins.

• The time delay indication disappears when the

programme starts and it is replaced by the remaining

programme time.

• Once having pressed the “Start/Pause” button,

the delay time can be reduced by pressing again the

“Start delay” button.

To cancel the “Start delay”

• Turn the programme selector to another position, or

press the “Start/Pause” button - the selected start

delay disappears from the display. Press “Start/

Pause” again if you want to start the selected

programme immediately.

FAILURE INDICATIONS

In case of any failures or irregularities, consult the

“Troubleshooting Guide” in your Instructions for Use.

“Service”

Lighting up of the “Service” indication can be caused

by a fault in an electrical component. Refer to the

“Troubleshooting Guide” in your “Instructions for Use”;

if the fault persists, contact our After Sales Service.

“Water tap closed”

The appliance has no or insufficient water supply. Open

the water tap: if the indications still lights up, refer to the

“Troubleshooting Guide” in the Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether the

drain hose is kinked or the filter must be cleaned: in the

latter case refer to the Instructions for Use (“Removing

the Filter”).

Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with

respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.Water and energy consumption refer

to the default setting of the programmes; selecting special options or modifying spin speed or temperature will change the consumption data.

The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also

“Troubleshooting Guide” in your Instructions for Use).

* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

** Reference Programmes for Energy Label.

*** Automatic adaption of programme duration after detection of wash load.

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

without “Rapid”

(kWh)

Approx. Programme Duration (hrs : min)

without “Rapid” with “Rapid”

Cotton 95 5.0 53* 1.70 2:00 -

Cotton ** 60 5.0 44 0.75 4:00 2:30

Cotton ** 60 2.5 32 0.65 2:20 ***

Cotton 40 5.0 49 0.60 2:45 1:45

Cotton ** 40 2.5 32 0.55 2:30 ***

Synthetics 60 2.5 50* 0.70 1:30 1:09

Synthetics 40 2.5 45 0.50 1:15 0:54

Sport 30 2.5 55 0.65 1:29 1:08

Delicates 30 1.5 50 0.50 0:45 -

Daily load 40 3.0 45 0.45 1:00 -

Quick wash 30 3.0 40 0.40 0:30 -

Wool 40 1.0 55 0.60 0:45 -

Handwash 40 1.0 45 0.60 0:40 -

Lingerie 30 1.0 45 0.50 0:36 -

Push the button(s) of any option(s) desired - the respe-

ctive indication lamp lights up.

When the combination of programme and additional op-

tion(s) is not possible, the indication lights switch off au-

tomatically. Unsuitable combinations of options are de-

selected automatically.

“Clean+” button

• Choose this option if you use an in-wash additive for

stain removal (powder, for example “Vanish”) - it will

optimize the additive’s efficiency to get better wash

performance and stain removal.

• Use with maximum load.

• Add an appropriate amount of in-wash additive for

stain removal (powder) to the main wash chamber,

together with your detergent (only use powder

detergent with this option).

Respect the manufacturer’s dosing instructions.

• Prolongs the programme by approx. 10 to 15

minutes.

• Appropriate for use of stain removers and bleaches

on oxygen basis. Chlorine or perborate bleaches

must not be used!

“Cold wash” button

• Water is heated only up to 20ºC.

• Suitable for delicate laundry items with wash

temperature recommendation of max. 30ºC on the

care label.

• Selectable only on the lowest temperature step

of each programme.

“Intensive rinse” button

• More water is added and rinse cycle is prolonged.

• This option is particularly suitable for areas with very

soft water, washing baby linen and helps people with

allergies.

“Easy ironing” button

• Can be used together with “Cotton”, “Synthetics”

and “Daily load” programmes to make ironing easier.

• Increases the water quantity and the clothes are spun

very gently.

“Rinse hold” button

• The laundry remains in the last rinse water without

pregressing to the final spin cycle to avoid creasing

and prevent colours from changing.

• It is particularly useful if you want to postpone

spinning to a later time, or if you want to drain only.

Note: The programme stops to “Rinse hold” at the

time the “Rinse hold” lights in the preogramme

sequence indication is on. The indication lamp next

to the “Start/Pause” button blinks.

Terminate the “Rinse hold” option:

• Press the “Start/Pause” button; the programme

will terminate automatically with the final spin cycle

for the present wash programme.

• If you do not wish to spin the clothes, turn the

programme selector knob to the “Drain” programme

and press the “Start/Pause” button.

“Spin” button

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If spin speed “0” is selected, the final spinning is

cancelled but intermediate spin peaks remain during

rinse. The water is drained out only.

“Prewash” button

• Only for heavily soiled loads (for example sand,

granular dirt). Increases the cycle time by

approximately 15 min.

• Do not use liquid detergent for the main wash when

activating the “Prewash” option.

“Rapid” button

• Enables quicker washing by shortening the

programme duration.

• Recommendable for small loads or only lightly

soiled laundry.

5019 801 01009

Polar PFL 1021-D Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info