Bedienungsanleitung Polti Vaporella Power System (Seite 8 von 8) (Englisch)

648863

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

VAPORELLA POWER SYSTEM

FOR YOUR OWN SAFETY READ FOL-

LOWING INSTRUCTIONS CAREFULLY

BEFORE ATTEMPTING TO CONNECT

THIS UNIT TO THE MAINS.

((

))

This unit is designed to operate on 240V, 50 Hz

current only. Connecting it to other power

sources may damage the unit.

WARNING - This appliance must be earthed.

This appliance may be fitted with a non rewirable

plug, if it is necessary to change the fuse in a non

rewirable plug the fuse cover must be refitted. If

the fuse cover is lost or damaged, the plug must

not be used until a replacement, available from

the appliance manufacturer, is obtained. It is im-

portant that the colour of the replacement fuse

cover corresponds with the colour marking on the

base of the plug.

If the plug requires to be changed because it is

not suitable for your socket, or becomes dam-

aged, it should be cut off and an appropriate plug

fitted following the wiring instruction (below). The

plug removed must be disposed of safely as in-

sertion into a 13A socket is likely to cause an

electrical hazard.

IMPORTANT

These wires in this mains lead are coloured in ac-

cordance with the following code.

• Green-and-yellow: Earth

• Blue: Neutral

• Brown: Live

As the colours of the wires in the mains leads of

this appliance may not correspond with the

coloured markings identifying the terminals in

your plug, proceed as follows:

The wire which is coloured green-and-yellow

must be connected to the terminal in the plug

which is marked with the letter “E” or by the earth

symbol or green-and-yellow.

The wire which is coloured blue must be connect-

ed to the terminal which is marked with the letter

“N” or coloured black.

The wire which is coloured brown must be con-

nected to the terminal which is marked with the

letter “L” or coloured red.

GREEN

YELLOW

(Earth)

BLUE

(Neutral)

FUSE

(13 amp)

BRAWN

(Live)

nector (S) (fig. 10).

• Unscrew the safety screw (R).

• Pull Vaporella outwards, so as to unlock the

pivot (W), on Vaporella’s back, from the

board locking support (X) (fig. 11).

• Lift up Vaporella.

• Turn Vaporella so that it can be separated

from the ironing board as shown in fig. 12.

• To connect Vaporella to the ironing board

again, proceed in the opposite way from

what stated above.

NOTE: During connection and disconnection

operations, make sure that the cable (D) is not

wound around its support (Q) and that the cap

(A) is screwed to prevent water leaking.

The board can be easily transported thanks to

its wheels (L); hold it on the side opposite to

Vaporella, lift it and push it (fig.13).

• Before attempting any maintenance

operation, always disconnect the ap-

pliance from the mains.

• To clean the body of the appliance, simply

use a moist cloth. Do not use solvents or

detergents which may harm the body mate-

rial.

vl power system m0s06959 1l12.qxp 18/01/2006 15.37 Pagina 31

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Polti Vaporella Power System Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Polti Vaporella Power System

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info