Bedienungsanleitung Polti Vaporetto Lecoaspira Program (Seite 20 von 35) (Englisch)

648717

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

LECOASPIRA PROGRAM

ENGLISH

♦ To select a pre-set programme, press the SET key (3).

♦ When the indicator (8A) starts to flash, it is possible to select the desired programme with the UP

(4) and DOWN (5) keys.

♦ Press the OK (2) key to confirm the selection.

The boiler turns on automatically in the 1 to 3 programmes. Wait until the indicator (8B)

stay lit. This means that the steam pressure corresponds to the one necessary to use the pre-set

programme. The appliance is now ready to be used.

It will only be necessary to press the steam button (A5), except for the P0 programme which is suc-

tion only and starts by pressing the suction button (A4).

Based on the programme selected, there will be an alternating sequence of steam and suction.

In order to guarantee the maximum safety of the user, European Regulation 60335-2-54

envisages that the supply of steam must occur in a voluntary manner. Because of this, when the

programmes described were developed, it was not possible to automate the steam supply function.

PROGRAMME P1 - Rugs, Carpets

This programme combines steam and suction to wash, vacuum and sanitise rugs and carpets.

♦ Set the P1 programme described in the paragraph “Pre-set programmes”.

♦ Holding the steam button (A5) down, steam is supplied

♦ When releasing the button (A5) or after a maximum of 150 seconds, the suction starts automati-

cally to dry the treated surface.

♦ Suction stops automatically after a period of time in proportion to the time the steam was sup-

plied.

♦ If you need to restart the programme to complete cleaning the entire surface, just press the but-

ton (A5) again.

PROGRAMME P2 - Parquet / Terracotta

This programme is specifically for cleaning parquet and delicate floors. The function involves the

combined action of a delicate intermittent flow of steam with adequate suction force. Delicate sur-

faces must always be cleaned using the special parquet cloth (O3) provided, fitted onto the univer-

sal brush (C) (Fig. D).

♦ Set the P2 programme described in the paragraph “Pre-set programmes”.

♦ Holding the steam button (A5) down intermittent steam is supplied and at the same time suction

starts.

♦ Release the button (A5) to stop the steam flow, while suction will continue for a few seconds more

to dry the surface treated.

♦ If you need to restart the programme to complete cleaning the entire surface, just press the but-

ton (A5) again.

Please pay careful attention when cleaning wooden surfaces and treated terracotta floo-

ring with steam as prolonged use of steam may damage the wax, polish or colour of the surfaces

to be cleaned. We therefore recommend dispensing steam on these surfaces only for short periods

of time and suggest always using a cloth, avoiding direct steam being dispensed onto the surface.

In the case of old or particularly delicate floors, clean with cloth steamed previously, without dispen-

sing steam directly on the surface.

Before steaming surfaces, we recommend vacuuming up any hair or dust, using the

vacuum only.

NOTE

LECOASPIRA PROGRAM - M0S10133 - 1T10:Layout 1 23/10/2013 9.45 Pagina 49

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Polti Vaporetto Lecoaspira Program Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Polti Vaporetto Lecoaspira Program

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info