Bedienungsanleitung Polycom Vortex EF2280 (Seite 45 von 105) (Englisch)

628495

Zoom out

Zoom in

Vorherige Seite

1/105

Nächste Seite

ERROR#040

This error occurs as the result of an

AMASGN command. It happens when the command would

remove a microphone from an automixer where it is assigned as the "last mic on" and the

automixer is set to manual "last mic on" mode.

ERROR#041

This error occurs as the result of an

AMASGN command. It happens when the command would

remove a microphone from an automixer where it assigned as the chairman imcrophone and

the automixer has chairman mode enabled.

ERROR#042

This error occurs as the result of an

AMLMM command. It happens when the command

attempts to set "last mic on" mode to manual, but the last mic number is set to a microphone

that does not belong to the specified automixer.

ERROR#043

This error occurs as the result of an

AMLMN command. It happens when the command

attempts to set a "last mic on" number that does not belong to the specified automixer while

"last mic on" mode is set to manual.

ERROR#044

This error occurs as the result of an

AMCHAIR command. It happens when the command tries

to enable chairman mode, but the chairman microphone is set to a microphone that does not

belong to the specified automixer.

ERROR#045

This error occurs as the result of an

AMCHAIR command. It happens when the command tries

to set the chairman microphone to a microphone that does not belong to the specified

automixer while chairman mode is enabled.

ERROR#060

This error occurs when the user has attempted to utilize more variable DSP resources than are

available. This may occur if too many matrix crosspoints are unmuted or too many parametric

EQ filters are enabled. The

DSPLOAD command can query the current percentage utilization of

DSP resources.

ERROR#070

This error occurs as a result of a macro or preset execution command (

PRESETX, PRESETQ,

MACROX, MACROQ). It indicates that the macro or preset requested was empty.

ERROR#071

This error occurs as a result of a

PRESETW or PRESETK command. In the case of PRESETW it

indicates that an attempt was made to write to a factory preset, which is not allowed. In the

case of

PRESETK, it indicates that an attempt was made to delete a factory preset, which is

not allowed.

ERROR#072

This error occurs as a result of a

PRESETQ command. It indicates that one or more commands

in the preset had errors during execution.

ERROR#073

This error occurs as a result of a

MACROA command when there are already too many

commands in the macro. The limit is 256 commands per macro.

ERROR#074

This error occurs in response to a

MACROA or a logic pin (LIA, LIH, etc.) command. If the

command written to the macro or logic pin is illegal, then this error occurs.

ERROR#075

This error occurs when a command attempts to write non-volatile memory, but non-volatile

memory is password protected via

NVLOCK.

ERROR#076

This error occurs when attempting to add a macro command (either during an upload or while

writing a single macro) and the Vortex runs out of room in non-volatile memory. As a result,

the entire macro is discarded. If this occurs during an upload, all previous macros (before the

one that caused the error) are written successfully.

ERROR#077

This error occurs when attempting to add a command to a macro, but the Vortex is not in the

process of writing a macro. This may happen if you forget to do a MACROS or UMACROS

command, or if you had an ERROR#076 and continued trying to add commands.

ERROR#090

This error indicates an EF Bus hardware handshaking error. This could happen if bussed units

are not powered on simultaneously. Powering the units up simultaneously should remove the

error.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Polycom Vortex EF2280 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Polycom Vortex EF2280

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info