Bedienungsanleitung Polycom Vortex EF2280 (Seite 69 von 105) (Englisch)

628495

Zoom out

Zoom in

Vorherige Seite

1/105

Nächste Seite

F01LOEN?

Query automatic logic output status messages.

F01LOENx , where x is 0 or 1 depending on the

current setting of LOEN.

8.77. LOK -- Delete One or All Logic Output Pin Commands

This command "kills" or deletes all commands for a given logic output pin. In other words, the commands

associated with

LOA and LOD will be deleted for the specified logic output. A wildcard character can also be

specified for the logic output pin, in which case the commands for all logic output pins will be deleted.

Using this command is more efficient than deleting one command or pin at a time since this command deletes

them all at once and requires fewer writes to non-volatile memory.

This command is saved to global non-volatile memory and is not part of a preset. Its value is saved each time it

is changed. It will retain its value after power-down. Since this command writes to non-volatile memory, there

will be a delay before an acknowledgment is returned.

Example Description Status Message

F01LOK5

Delete all the commands associated with logic output pin 5. This one command is

equivalent to executing the commands 'F01LOA5, ' and 'F01LOD5, ' except that

this command is more efficient.

F01LOK5

F01LOK*

Delete all the commands associated with all logic output pins. This one command

is equivalent to executing the commands 'F01LOA1, ' and 'F01LOD1, ' for each

logic output, except that this command is much more efficient.

F01LOK*

8.78. LOM -- Mask Logic Output Pins

This command is used to mask (i.e., disable) logic output pins. The mask consists of 20 fields (one for each logic

output) that can each be set to 0 or 1. If the mask bit for a given logic output is set to 1, then the logic output

pin works normally. If the mask bit for a given logic output is set to 0, then the logic output is disabled. When a

a logic output is disabled, it is "frozen" in whatever state it is in when it is disabled. The output pin's state will not

change when the condition that drives it (via

LOA and LOD) changes. However, any changes to that pin caused

by setting the values with an

LO command will affect the output pin value. For instance, you could disable

(mask) a pin and then explicitly set its value to low with the

LO command.

When a logic output pin is re-enabled, it will be updated to the current status of whatever condition drives it (via

(

LOA and LOD).

This command is saved to non-volatile memory only as part of a preset. The state of this command will be

restored after power-up only if a preset is saved and that preset is set to be the power-on preset.

Example Description Status Message

F01LOM10010110111101111111

Mask (disable) logic

outputs 2, 3, 5, 8,

and 13.

F01LOM10010110111101111111

F01LOM?

Query current logic

output mask.

F01LOMabcdefghijklmnopqrst , where a-t are

each 0 or 1 depending on the current state of the

logic output mask.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Polycom Vortex EF2280 Seite 69

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Polycom Vortex EF2280

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info