Bedienungsanleitung Polycom Vortex EF2280 (Seite 102 von 105) (Englisch)

628495

102

Zoom out

Zoom in

Vorherige Seite

1/105

Nächste Seite

Example Description Status Message

F01SSEN1

Enable screen saver.

F01SSEN1

F01SSEN0

Disable screen saver.

F01SSEN0

F01SSEN2

Toggle screen saver enabled state.

F01SSENx , where x is 0 or 1 depending on the current

enabled state of the scrren saver.

F01SSEN?

Query screen saver enabled state.

F01SSENx , where x is 0 or 1 depending on the current

enabled state of the scrren saver.

8.132. SSSTART -- Set Idle Time Required for Screen Saver to

Start

This command sets or queries the amount of time (in milliseconds) that the front panel buttons must be idle

before the screen saver starts.

This command is an integer command. See

Section 6.2 for more information on this type of command. The

minimum and maximum values for this command are 500 and 600000, respectively.

This command is saved to non-volatile memory only as part of a preset. The state of this command will be

restored after power-up only if a preset is saved and that preset is set to be the power-on preset.

Example Description Status Message

F01SSSTART2000

Set screen saver start time to 2

seconds (2000 ms).

F01SSSTART2000

F01SSSTART>500

Increase screen saver start time by

0.5 seconds (500 ms).

F01SSSTARTx , where x is the new value of the

screen saver start time. If this command was issued

after the example above, then the status message

would be F01SSSTART2500 .

F01SSSTART?

Query screen saver start time.

F01SSSTARTx , where x is the new value of the

screen saver start time. If this command was issued

after the example above, then the status message

would be F01SSSTART2500 .

8.133. SSTEXT -- Set Text to be Displayed by Screen Saver

This command sets or queries the text messages displayed by the screen saver. The arguments of this command

are the screen number, the line number, and the text to be displayed. The screen number must be between 0

and 3. It indicates which message screen we are trying to set or query. Each message screen consists of two

lines of text that can be up to 16 characters long. The second number indicates which line of the message we

are tring to set or query. The line number must be 0 or 1 corresponding to the first and second line, respectively.

Finally, the text argument is the actual text that will be displayed on the LCD. If the text is '?', then a query will

be performed. If the text empty, then the message will be cleared. If both message lines are cleared for a given

screen, then that screen will not be displayed by the screen saver. If all screens have been cleared, then the

screen saver will never start (although it is easier just to use the

SSEN command for this).

This command is saved to non-volatile memory only as part of a preset. The state of this command will be

restored after power-up only if a preset is saved and that preset is set to be the power-on preset.

Example Description Status Message

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Polycom Vortex EF2280 Seite 102

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Polycom Vortex EF2280

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info