Bedienungsanleitung Power Dynamics PBA30 (Seite 5 von 24) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Polnisch)

770413

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

100V LINE SYSTEM

For 100V line systems, connect the amplifier to the first speaker in the system using double-insulated speaker wire which has

adequate current rating to handle the total output of the amplifier.

Connect the “100V” output terminal to the positive (+) connection of the speaker and “COM” output to the negative (-)

connection of the speaker. Connect further speakers in parallel to the first speaker with all positive terminals and connected

together and all negative terminals connected together as shown below.

A 100V line speaker system can comprise of many speakers connected together. The determining factor for how many

speakers can be used on a single amplifier is the power rating. For most purposes, it is advised to connect as many speakers

as needed with a combined wattage of no more than 90% of the amplifier’s output power rating.

The terminals of a 100V speaker are connected to a transformer and in some cases, this transformer may be “tapped” for

different power ratings. These tapings can be used to adjust the wattage (and output volume) of each speaker in the system to

help achieve the ideal total power of the system for the amplifier.

SPEAKER TERMINALS

These terminals are offering 3 low voltage outputs 4Ω, 8Ω, 16Ω depending on your speaker combination. A 70V/100V

commercial output is also available.

Please note that one wire only should be connected to COM screw and one wire to the selected impedance or voltage.

ATTENTION: Multiple combinations cannot be done at the output level.

Four different types of connections are provided. The low impedance section: 4Ω, 8Ω, 16Ω is designed for a small amount of

speakers to be connected to your amplifier. The 70V/100V section is especially designed for a multiple speaker distribution.

When using the 70V/100V output, speakers have to be equipped with 70V/100V transformer. The maximum amount of

speakers to be placed on your distribution line is in relation to the power allocated to each speaker. The total wattage set on the

secondary side of the transformers on your speaker line must not exceed the maximum RMS output power: 30W, 60W or

120W. Failure to respect this may cause permanent damage to the amplifier.

OPERATION STEPS

• When all connections to the amplifier are made, turn all rotary controls down and switch on the power and a power “ON”

LED will illuminate. Turn BASS and TREBLE controls to the 12 o’clock position (pointing straight up) and turn MASTER

rotary control up part way for testing.

• Ensure a signal is being fed to one of the line inputs 1, 2, 3 or 4 and gradually increase the volume control for that channel

until the output is heard through the speakers. Turn up the MASTER to the maximum required volume level and reduce the

channel volume control if necessary.

• Note: The initial test can be made using the built-in USB/SD/FM audio player. The output of the amplifier is represented on

the level meter LEDs and care should be taken that the Red “0” LED is only lit momentarily during use. Anything longer

than a short flash of this LED may be indicating distortion or clipping of the output signal and the MASTER should be

turned down.

• If a microphone is connected to MIC1 input, make sure it is switched on and if it requires phantom power, make sure this

feature is enabled. Gradually increase its volume control whilst speaking into the microphone until the required volume

level is reached. The microphone should not be able to “hear” the speakers, which can cause feedback (squealing or

howling noise).

• In addition to channel and MASTER volume controls, there are BASS and TREBLE EQ controls to adjust the tone of the

overall output. At the 12 o’clock position, these controls are applying no effect to the signal (no boost or cut). Moving the

BASS control clockwise boosts the low frequencies in the audio, whilst moving it anticlockwise will cut these low

frequencies. Likewise, moving the TREBLE control clockwise boosts the high frequencies in the audio, whilst moving it

anticlockwise will cut these high frequencies. Adjust these EQ controls to suit the type of audio signal or compensate for

the room acoustics.

REPLACING THE FUSE

If the fuse is defective, replace the fuse with a fuse of the same type and value. Before replacing the fuse, unplug mains lead.

Procedure: Step 1: Open the fuse holder on the rear panel with a fitting screwdriver.

Step 2: Remove the old fuse from the fuse holder.

Step 3: Install the new fuse in the fuse holder.

Step 4: Replace the fuse holder in the housing.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Power Dynamics PBA30 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info